The Integrated Services Digital Network (ISDN) Basic Rate
Interface (BRI) provides which of the following?
A.) 1.544 Mbps
B.) 23B + 1D Channel
C.) 24B + 1D Channel
D.) 2B + 1D Channel
E.) 23B + the Disney Channel
Answers were Sorted based on User's Feedback
Answer / guest
Answer: D
Each B (Bearer) Data channel is 64K
The D (Control) channel is 16K
Is This Answer Correct ? | 5 Yes | 0 No |
Identify the switching method that examines the destination MAC address as the frame is being received then begins forwarding the frame prior to receiving the entire frame? A.) Fragment-free B.) Store and Forward C.) Cut-through D.) Fast forward
Explain how many ways to access router?
what is ESP (Encapsulating Security Payload)?
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
What are two functions of the ICMP protocol? (Choose two) A. to map IP addresses to Ethernet addresses B. to map common names to network addresses C. to forward SNMP alerts to management consoles D. to generate an echo reply in response to a ping test E. to send a host or pod unreachable message from a router to the source of an undeliverable packet
What is the syntax to add a banner to the Cisco router? A.) motd banner # B.) banner C.) banner motd # D.) banner #
. Which command sequence will allow only traffic from network 185.64.0.0 to enter interface s0? A. access-list 25 permit 185.64.0.0 255.255.0.0 int s0 ; ip access-list 25 out B. access-list 25 permit 185.64.0.0 255.255.0.0 int s0 ; ip access-group 25 out C. access-list 25 permit 185.64.0.0 0.0.255.255 int s0 ; ip access-list 25 in D. access-list 25 permit 185.64.0.0 0.0.255.255 int s0 ; ip access-group 25 in
What is the meaning of PASSIVE interface in RIP, IGRP, EIGRP & OSPF?? Can any one explain..!!!
Which commands should you use to enable IGRP routing? A. router igrp 100 Network 192.168.1.0 Network 10.0.0.0 B. router igrp 100 Network 192.168.2.0 Network 10.0.0.0 C. router igrp 100 Network 192.168.1.0 192 168.1.1 Network 10.2.0.0 10.2.1.1 D. router igrp 100 Network 192.168.1.0 255.255.255.0 Network 10.2.0.0 255.255.255.0
What is the difference between communication and transmission?
Identify the command that displays traffic statistics on serial0/1? A.) display interface serial0/1 B.) show interface serial0/1 C.) show seria0/1 stats D.) show interface serial0/1 stats
Which works router do?