Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...

Instrumentation Interview Questions
Questions Answers Views Company eMail

what is the difference b/w magnetic flow meter&mass flow meter? which one is best?

1 5831

what is span adjusment of transmitter? what is the function of positioner/

Kent,

2 5775

how to change measuring units from mmwc to cubm/h in rosemount air flow transmitter with hart communicator fluke 744

1681

what is the current pay package for an instrumentation engineer having 2 years of experience in cryogenic technology???????

1 4012

WHAT IS THE MASS FLOW FLOW METER

Reliance,

4 6958

Can DP transmitter with orifice plate works on Beta ratio 0f 0.3 and differential pressure of 100 MMWC in liquid service application?

1 4165

What is a flow meter?

2 5250

why we use by pas on a positioner? When can a by pass be not used on a positioner ?

1 4531

why we use by pas on a positioner? When can a by pass be not used on a positioner ?

2 5858

Q-Explain the different load conditions that will produced different offset which may or may not be acceptable to thhe control function

Reliance,

1587

what is maxdna ?. explain about the software details.

3717

control panel design guidelines

2683

i m passed my engineering in 2010 in instrumentation and control engineering. my question is can i apply for software jobs or vacancies.??????????? plz give me answer soonnn......

2 3341

why is negative range given to measure the steam drum level

Jindal,

2 15306

what is the zero elevation and zero supresstion in level measurement, how can use it?

GAIL,

2 5812


Post New Instrumentation Questions

Un-Answered Questions { Instrumentation }

How to find out the current of two motors having same power consumption but different RPM?

1371


what are the use of belew gear in general ??

1392


i have done DAE in Instrumentation and Process Control. i have applied for an apprentice training in chemical company after three day my interview will be conduct but i need more information about industrial process control and controller. my e mail is imran_dilsetu@yahoo.com please tell me interview question relative to instrumentation ?

1671


Can I route 110 VDC and 24 VDC in a same Duct for our Interposing relay cabinet? IF yes or NO Please provide me IEEE Std. for the same. Please i required it on Urgent basis, i need to design IRP Cabinets and we have MCC 110VDC and Our Coil side is 24VDC, Please help as soon as possible.

1619


Is it ok, to use non-contact type Radar type LT, on a tank that is half circular from the bottom side? If yes the, isn't the waves gonna bent in other directions? 

1499






Meaning of the following a. IOP- Manimum; b. IOP- Maximu,;

1427


where are following valves are applicable to install. can any valve be installed any line. globe valve butterfly valve boll valve gate valve

1072


what is the difference between scaler and vector drive

1492


I want to buy a seal kit of a pneumatic power cylinder.But I don't know it's specification.So please help me to know its specification.

1344


what is interface level and how it is calibrate?

1610


Please asked me How calculate DCS controller memory.

2171


what is the field bus calble ? what are diffrences in orang colur cable and black coular calble ?

2243


what is SIL 1 2 3

1312


SOME OF YOUR QUESTIONS ARE NOT MAKING ANY SENSE SO TRY AND PUT IN A LITTLE BIT MORE EFFORT BEFORE YOU POST A QUESTION. WE WILL ONLY HELP THOSE WHO WE CAN SEE ARE TRYING TO HELP THEMSELVES.

1772


how to calibrate mass flow meter (Coriolis)? Example calibration range: 0 to 2500 kg/hr line size 3" fluid: Etheline glycol (MEG)

2099