Answer / chitesh shankar

CDMA stands for CODE DIVISION MULTIPLE ACCESS while GSM is GLOBAL SYSTEM FOR MOBILE COMMUNICATION.

In GSM, FDMA( Frequency Division Multiple Access) and TDMA (Time Division Multiple Access) are togetherly used.

Answer / siddhu

cdma acronym is "code division multiple access" .It works
by assigning a particular code to subscriber while making a
call so that it has flexible bandwidth to use...

where as gsm acronym is global system for mobile
communication it does us different frequencies and
bandwidth . its quality is far better compared to cdma...

Answer / srajan tiwari

in gsm we have different chanels,but in cdma only a single channel exist.... in gsm.. as there are different channels,,,
handoffs are required..in cdma as single channel is present handoff is a unknown ,,extra terrestrial word ..i.e. it does not exist.. freq reuse concept is essential in gsm.. and it is a stupid word for cdma as single channel is shared....

Answer / vikash sharma

cdma is use wide band spectrum while gsm use narrow band spectrum.

Answer / mohd.afzal jani

A Mobile station (MS) is attached to the GSM (PLMN)public
land mobile network through the Um interface.


The user in the code space be separated by using code with
some characteristics, so that they can access the shared
medium uninterruptedly Code division Multiple Access(CDMA)
implements such scheme.

Answer / abhinav palhade

in cdma, fdma & tdma together are used.in gsm,there are no
such fundas.there are different freq bands in cdma and the
n/w user is shifted or assigned over another band after
some amount of time.but in gsm, many users are bounded tyo
ese same freq band.thats why we get clear n/w in cdma.

Answer / vikas singla

yes you are genius this is avery good answer

What is a comparator?

0 Answers  

friends, in closed loop system bandwidth is encresed comparision to open loop. what is mean by that? generally bandwidth means something realeted to frequency.

1 Answers   BARC,

Explain is rfid in developing stage? What is scope in rfid?

0 Answers  

idea uses the 1800mhz band with alloted 4.4mhz bandwidth. this band is divided into 22 channel(up link).how will operator divides these channel in to traffic channel and control channel. explain

0 Answers   Idea,

how a definite tx line can acts as indefinite tx line

0 Answers   Bosch,

How to E1 cable get 2.046 mbps.

0 Answers  

What is D-FF? What is the basic difference between Latches and Flip flops? What is a multiplexer? How can you convert an SR Flip-flop to a JK Flip-flop? How can you convert an JK Flip-flop to a D Flip-flop? What is Race-around problem? How can you rectify it? Which semiconductor device is used as a voltage regulator and why? Explain an ideal voltage source? Explain zener breakdown and avalanche breakdown? What are the different types of filters? What is the need of filtering ideal response of filters and actual response of filters? What is sampling theorem? What is impulse response? Explain the advantages and disadvantages of FIR filters compared to IIR counterparts. What is CMRR? Explain half-duplex and full-duplex communication? Which range of signals is used for terrestrial transmission? Why is there need for modulation? Which type of modulation is used in TV transmission? Why we use vestigial side band (VSB-C3F) transmission for picture? When transmitting digital signals is it necessary to transmit some harmonics in addition to fundamental frequency? For asynchronous transmission, is it necessary to supply some synchronizing pulses additionally or to supply or to supply start and stop bit? BPFSK is more efficient than BFSK in presence of noise. Why? What is meant by pre-emphasis and de-emphasis? Explain 3 dB cutoff frequency? Why is it 3 dB, not 1 dB? Explain ASCII, EBCDIC?

3 Answers   DRDO, Electronics,

filtering can be done with: i)capacitor,ii)inductor,iii)both,iv)none.

18 Answers   CTS, Verifone,

What is the total resistance between points ‘A’ and ‘B’ in the given circuit

4 Answers  

Explain the different modes of flyback converter

0 Answers  

Micro controller input pin voltage is max 5v. If i want give 50 0r 100v input pin. whether is it possible

4 Answers  

describe the functioning of parallel adder ? what are the adventages of parallel adder over series adder?

0 Answers