what is difference b/w HT & LT and the range of HT & LT ?

Answers were Sorted based on User's Feedback



what is difference b/w HT & LT and the range of HT & LT ?..

Answer / mike

Less say if you had transformer in a station it was a 100kv
to 44kv the breaker between the bus an high side of the
transformer protecting it from a fault would be the high
tension. Once it leaves the low side of the transformer it
goes to a breaker that is between the transformer and the
low side bus this would be your low tension. These breakers
have ct that protect the bank with differiential relays.

Is This Answer Correct ?    12 Yes 30 No

what is difference b/w HT & LT and the range of HT & LT ?..

Answer / chandru

ht - high voltage transmission
Lt - low voltage transmission

Is This Answer Correct ?    35 Yes 60 No

Post New Answer

More Electrical Engineering Interview Questions

what is the use of surge suppresser in 33 KV incoming panel. where it must be installed,inseries with incoming cable surge suppresser must be at incoming of the breaker are outgoing of the breaker

1 Answers   Siemens,


some time we open engine breaker 8.0 MW load but plant not trip. and another time engine open 4.0 MW load engine trip why? individually engine breaker open & individually emergency stop why difference?

0 Answers  


WE HAVE A PROBLEM THAT THE MAIN DRIVE OF OUR CEMENT MILL HAS AN EARTHING PROBLEM?TWO OF STATOR WINDINGS INSULATION HAS BEEN COLLAPSED DUE TO AGING PROBLEM.THE PHASES HAVE BEEN BYPASSED AND NOW THE LOAD HAS BEEN INCREASED.WE CAN'T REPLACE THE MOTOR.KINDLY HELP ME BY GIVING SUGGESTION THAT HOW TO MAINTAIN THE STARTING TORQUE AND CURRENT FOR HIGH LOADS.

1 Answers   ACC,


Why capacitor bank is not neccessery to switch on,pls answ me with formula

2 Answers  


What is the difference between power cable and signal cable (only Observation Difference)?

1 Answers  






Why annealing is done on transformer core manufacturing process?

1 Answers   ISRO,


why we are using large cross section cable at load side and small at other (11kv to trsfr)side of transformer? when the load increses current at both side increases,right?

2 Answers  


Why is voltage is required to be within permissible range for an electrical equipment?

0 Answers  


Whats difference between a single phase & a three phase motor?

4 Answers  


What is substation?

5 Answers   KSEB, Neolite,


in VFD when freq is reduce the voltage will reduceor not if it will reduced upto ...

8 Answers  


What is the difference between LT CT & HT CT?Can we use indoor type transformer as an outdoor type or vice versa?

2 Answers   Bhel,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)