Answer / suresh

i call ambulance van

Answer / ramana reddy

first icall to ambulance then i will do first aid depending
upon injury

Answer / vani

immediately call the ambulance and before the ambulance
comes do sufficient treatment such as giving water to the
injured person and do minimal treatment so that he is not
injured more.

Answer / johnanand

make a call for ambulance... other wise i have an vehicale
i can admit in to hospital in case of emergency

Answer / sravanthi

fisrt of all i try to clear the crowd around him and give
him minimal first aid and call to ambulance

Answer / praveen

first i will call ambulance and i do first aid for him
depending upon injury

Answer / veerababu

i will call 108 ambulance

Answer / rajneesh

first giving the first-aid & call ambulance

Answer / durgesh agarwal

First of all i will call ambulance and before coming to the
ambulance i will give some first-aid as much as i can.
if ambulance don't come with in 5 minutes then i will carry
that person to the hospital.but all depends on circumstances.

Answer / mohd junaid

Ist i will see the condition of injured person.Then i will
took these step on priority
I feel he is not more injured try to took him for treatment
to the nearest clinic by any vehicle
If he is more injured then i took him to safe side and then
call to ambulance

POLYMER ENGINEERING - QUESTION 24.3 : The molecular weights M in kg / mol of 3 different monomers a, b and c in a polymer are Ma = 14, Mb = 16 and Mc = 18, with their respective quantities in N units having the ratio of Na : Nb : Nc = 2 : 3 : 5. (a) Find the numerical average molecular weight of the polymer by using the formula (Ma Na + Mb Nb + Mc Nc) / (Na + Nb + Nc). (b) Find the weighted average molecular weight of the polymer by using the formula (Ma Na Ma + Mb Nb Mb + Mc Nc Mc) / (Ma Na + Mb Nb + Mc Nc). (c) Calculate the polydispersity Q by using the answer in (b) divided by answer in (a). (d) Find the volumetric average molecular weight of the polymer by using the formula (Ma Na Ma Ma + Mb Nb Mb Mb + Mc Nc Mc Mc) / (Ma Na Ma + Mb Nb Mb + Mc Nc Mc). (e) Estimate the polydispersity Q by using the answer in (d) divided by answer in (b).

1 Answers  

what is chemical engineering?

2 Answers  

When using a pumping loop to mix two miscible fluids in a tank, when can the content are considered well mixed?

0 Answers  

Question 49 - According to rules of thumb in chemical process design, consider the use of an expander for reducing the pressure of a gas when more than 20 horsepowers can be recovered. The theoretical adiabatic horsepower (THp) for expanding a gas could be estimated from the equation : THp = Q [ Ti / (8130a) ] [ 1 - (Po / Pi) ^ a ] where 3 ^ 3 is 3 power 3 or 27, Q is volumetric flowrate in standard cubic feet per minute, Ti is inlet temperature in degree Rankine, a = (k - 1) / k where k = Cp / Cv, Po and Pi are reference and systemic pressures respectively. (a) Assume Cp / Cv = 1.4, Po = 14.7 psia, (temperature in degree Rankine) = [ (temperature in degree Celsius) + 273.15 ] (9 / 5), nitrogen gas at Pi = 90 psia and 25 degree Celsius flowing at Q = 230 standard cubic feet per minute is to be vented to the atmosphere. According to rules of thumb, should an expander or a valve be used? (b) Find the outlet temperature To by using the equation To = Ti (Po / Pi) ^ a.

1 Answers  

What is a 'saltation velocity' and how is it used in designing pneumatic conveying systems?

0 Answers  

What could be a possible cause for sudden foaming in a cooling tower?

0 Answers  

If the refrigerator is left open in closed room, What will be the effect on room temp.?

2 Answers  

How can you estimate the efficiency of a pump?

0 Answers  

Repected sir/Madam, I am goingb to face IOCL technical as well as HR interview, can you forward your hellpfull hand for toward me to sort out my problem by giving some imp interview quetion which is generally asked in chemical industries such like IOCL,HPCL,ONGC,BPCL,RIL,what is the difference in pump,blower & in compressor

0 Answers   IOCL,

Can anybody suggest the Methods/Procedures for estimation of oxygen, hydrogen, methane, carbon dioxide, CO, etc. in binary or complex gas mixtures?

2 Answers  

Explain what are the design considerations for a piping system for the transfer of slurries?

0 Answers  

What is the procedure to estimate the friction factor involved in heat exchanger tubes?

0 Answers