Answer / infodoss

depanding upon the form facter .. the value is 1.1 so
voltage variation depending upon this

Answer / opselvaraj

we do have 110kv,230kv,400kv which are not multiple of any
factor as discussed earlier.
It all depends on various factor and differs from country
to country.

Answer / d.durga prasad

According to i know, i am giving the answer that it will be depnd up on the form factor 1.1,according to that only we are getting the levels in the forms of 11,33,66,110,132 & 220KV, but ihave the doubt on that 400 & 765KV is depend up on wihich factor & if any one knows please answer.

Answer / p.satish

It is because of the form factor of the alternating
current. It is 1.1. So the rating becomes in multiples of 11

Answer / narasihman

i too dont know, if any one know the answer please help

Uses of induction motor

6 Answers   NTPC,

WHY EXCITER PHASE SEQUENCE ARE OPPOSITE THAN STATOR SUPPLY PHASE SEQUENCE IN SYNCHRONOUS MOTOR >

0 Answers  

1.why ACB is not connected in HT side what Happens? 2.how much voltage maintained in ACB breaker? 3.OLTC is connected in primary side in case secondary side connected what happened?

3 Answers   L&T,

what is the differenc between A.C. and D.C, which is more dangerious?

4 Answers  

Energy metering: On the property I am renting, the supply voltage is 2 x 110 volts. These 2 x phases enter a energy meter which then exit the meter to over head lines to my house. Question 1. The meter is single phase 240 volts but is being used as 2 x phase(2 x 110volt), is this acceptable? if not, please give me the reasons. The meter details are as follows: 60Hz 15amp Imax 100 amp Kd 3,6 Wh/R 1 fase 3 hilos Model FX 231. I think it was manufactured in Brasil From this meter, the cables run along over head aluminum conductors,I estimate the cross sectional area to be 25mm diameter, but the neutral is only about 10mm square diameter, which cover a distance of 170 meters and then terminate with an underground cable of 65 meter length, total length = 235 meters. There must be a huge voltage drop over this length. This line is protected with 2 x 200 amp aluminum fuses after the meter, there is no main switch in the distribution board. These 2 phases connect directly onto 2 busbars. Surely the neutral should be the same size as the conductors if not more? Question2. What are your thoughts about this installation, should there be better protection, is the neutral too small? During the night, the lights dim then brighten all the time, this cannot be good for my electrical appliances. In my home, I only have a small electric geyser and fridge, my stove works off gas. But when i use other appliances like the washing machine or microwave oven, the light dim. The internal wiring of this house is done with solid hard drawn copper wires and of course, they have to be under rated. I am a retired electrician by trade, but not on the metering and over head mains side, my experience is on the factory maintenance side of things. Your expertise on these matters will be greatly appreciated. Please inform me how to rectify or make any improvements Kind regards, my power bill is very expensive, so I need to know how to bring it lower. Kind regards, Brian

1 Answers  

What will be the capcity of 3 phase DG set require for 25 KVA single phase lighting load?

7 Answers   Supernova,

sir& friends i want the collection of recent quetions asked in interview of top most companies please send me on my email san.jsr@hotmail.com

0 Answers  

What happen Grid EARTH plat got cut.

0 Answers   Zuari,

what is lxr?

0 Answers   NTPC,

how to copy from plc ge fanuc versamax series,all input and output, adress, and printout.

0 Answers   ASM,

what is sevice settings for mccb?How can be it setted?

1 Answers  

how to put cable sizing and cable glands size for respective cable & Cable Lug size in a DB sectors???

0 Answers