Answer / welcome4ujd

you can use fluke milliampre simulator tocalibrate a
controlvalve through i/p converter, ot by using a druck
pressure calibrator directly to the controlvalve positioner.

Answer / upendrae

we can use the 4-20ma source for calibration of the electro
pneumatic valves.

Answer / tarun

CONTROL VALVE HAVE MOSTLY 3 PART BODY,BONNET AND
ACTUTOR,CONTROL VALVE REQUIRED AIR SUPPLY 20 PSI OR 140KPA
AND SIGNAL 4TO20MA AND TOOLS AND STANDURD P.G OR DRUCK. SO
FINNALY WE USE ENOMET SOURSE, DRUCK, OR REGULATOR AND AIR
SUPPLY REQUIRED

Answer / murugesan

First ensure both I/P and positioner air supply are as
it should be before starting up control valve
calibration/stroke checking activity. Then take any of loop
or multifunction calibrator based on the instrument
availability in your plant for Ex 707Ex, UPS-III-IS, UPS-
II, UPS-IS, DPI610 IS (connect series with 24 VDC supply),
UNOMAT and 725Ex

And select “mA source with 24V DC” option and connect 4-
20mA source to I/P converter and simulate appropriate mA to
check the stroke. Normally control valve stoke checking is
called as control valve calibration.

Answer / rushikesh s gaddpawar

CONTROL VALVE CALIBRATATION MANLY USE MA POWER SUPPLY
SOURSE TO CALIBRATE CONTROL VALVE

Answer / balu

WE CAN CALIBRATE IT THROUGH A MILLI AMPS FEEDER IN PRESENT
DAYS

Answer / ali faozy

if the control valve has i/p &postioner we need [ 4 to 20 ]
milliamper dc source , 140 kpa air supply for i/p and 700
kpa for positioner [depending on positioner supply
recommendation]
we need also to calibrate the strock indicator for fully
open and fully close positions
if the control valve has no i/p & positioner then we need
air signal source of [20 to 100]kpa depens on control valve
design
and 700 kpa air supply for valve supply

Answer / shabbir ahmad mughal

we use loop calibrater and miliampere source for
(pst)partial strok testing or calibration of control valve

what is loop1 and loop2 in MTS LT?

0 Answers   SPGC,

ALL INSTRUMENTS WORKING PRINCIPLE.

3 Answers   Blanco, India Cements, TVS,

why we use cascade control and feed forward control in 3 element drum level control measurement of steam drum .what is cascade and feed forward control system ?give example .

0 Answers   Visa Steel,

what is puling in n pulling out in flame scanner system?

1 Answers  

What is eddy current? Describe the operating principle of proximity probe.

0 Answers  

I am an intru engg frm pune n completing mba marketing in may 2010, what kind of profile would best suit my educational qualifications??? Also, i will move to US in jan 2011, so this job experience should count Over there too 'coz i want to continue workin even there....

1 Answers  

We have a Yokogawa Micro-XL DCS, which is having around 300 I/O, but whenever there is any wire gets grounded in field, the 24v supply to all loops gets dipped & all the indications at DCS goes to IOP(shows input open), at present we have fixed 500mA fuses in all the lines but which does not working. Does it required to replace with lower amps fuse, then how much or is there any other solution for this.

2 Answers  

wht is Zero Elevation and Zero Suppression?

12 Answers  

i have steam drum height 1000mm. and i want to placed the transmitter below the tap.how i calculate.

0 Answers   OEG,

How is SmartPlant Instrumentation related to INtools?

4 Answers   TCS,

Why using negative voltage in vibration measurement?

2 Answers  

what are the different types of Protocols? & their applications.

6 Answers   Infosys, Sitara Chemical Industries, Syntel, VSNL,