What do you mean by linear and bilateral network?
Answers were Sorted based on User's Feedback
Answer / deepak
linear network
the network whoes parameter does not change due change in
current or vtg. eg. resistance,inductance,capacitance.
bilateral network
the ckt whoes chara. does not change due change of
direction of vtg. & current. e.g. transsmisson line
Is This Answer Correct ? | 373 Yes | 66 No |
Answer / manoj k mishra`
LINEAR NETWORK -- a network in which the relation between
volatage and current is linear curve.
Bilateral- means the relation between voltage and current
does not change in both the direction in the network.
Is This Answer Correct ? | 245 Yes | 84 No |
Answer / ashok rajput
Linear Element are those element which follow the ohm's law.
Like as Resistance,Inductor&Capacitor(at relexed condition)
Bilateral network is that network in which any element of
the network gives the response in both directions e.g R,L,C
but diode gives the response in only one direction so it is
a unilateral element.
Is This Answer Correct ? | 88 Yes | 45 No |
Answer / ashu
LINEAR NETWORK: 1) A network if the relation between current and voltage involves a constant coefficient e.g V=IR or network response is proportional to excitation function.
2)A linear n/w is the one in which the principle of superposition(linearty test) holds.
BILATERAL N/W: When element properties & characteristics are independent of direction of the current then the n/w is called as bilateral n/w
Is This Answer Correct ? | 22 Yes | 8 No |
Answer / sum
linear are those network which obey's ohms law
bilateral r those in which current can flow in both directions
Is This Answer Correct ? | 70 Yes | 63 No |
Answer / shubhendu bhattacharya
A linear network should follow two rule (1)-superposition & (2)-homogeneity.Linearity means not only the equation is linear the line must pass through origin.
Is This Answer Correct ? | 5 Yes | 2 No |
Answer / anita manikpuri
Linear - all elements and branches of circuit is obey ohm's law is called linear network.
Bilateral - bilateral means if you give some source voltage and gain some output and then you use this output voltage in form of source voltage then you gain some output , it is a value of initial source voltage. It means both are equal and current independent.
Is This Answer Correct ? | 3 Yes | 1 No |
Answer / muhammad rehan qureshi
A circuit whose Characteristics, behavior is same irrespective of the direction of current through various elements of it. is called bilateral network. Network consisting only resistances is good example of bilateral network.
Is This Answer Correct ? | 5 Yes | 4 No |
Answer / mounika
example for this linear and bilateral network is
superposition theorem.
Is This Answer Correct ? | 8 Yes | 7 No |
Answer / yashotkarsh mani tripathi
A network in which the parameters of resistance, inductance,
and capacitance are constant with respect to current or
voltage, and in which the voltage or current of sources is
independent of or directly proportional to other voltages
and currents, or their derivatives, in the network. Also
known as linear circuit.
Is This Answer Correct ? | 2 Yes | 2 No |
what is mean by tan-delta tap in the potential transformer??
what is surge impedance loading?
where can i get the previous years question papers for APGENCO exam.
why C.T secondary are rated 5A generally?
According to ohms law voltage proportional to current, then why should current rating is low with high voltage rating in transformer?
10rm cable can got load ---- amp? Or Which Size Cable can take the load 100amp capacity SCR; breaker.
1 Answers B-Con Trade Associates,
What is triac?
why the transformer has no starter
May I know how much values to be set for earth fault, over current and short circuit values at 11kv side? I have 11kv van 1250amps rating. Present it's taking load 80amps?
What are the three types of compensators?
2.5mva transformer is installed in our company with oltc but it is not working in auto mode ,it is operative in manual mode control wiring is done how can i rectify it?
purpose of check value