Suppose there are two cylinders / vessels.In one cylinder
the pressure is 1.5 bar & in other 0.5 bar.If both cylinder
are connected internally through valve connection, what
will be the final pressure in both?
- 19 Answers
- 21202 Views
- BARC, Bhel, HPCL, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / raghu
I think it depends upon the volume of the two vessels.
if the two vessels are having same volume then final
pressure may be 0.866 bar
| Is This Answer Correct ? | 4 Yes | 8 No |
Answer / pavan
from the law of mixing of gases, the final presure after
micing two idial gases is, Pf=sqroot(p1*p2).
Pf=sqroot(1.5*0.5)=0.866bar.
| Is This Answer Correct ? | 6 Yes | 13 No |
Answer / jeraldineduzon
pf=sqroot so., (1.5*0.5) isequals to 0.866bar.,
yeah!!\
| Is This Answer Correct ? | 2 Yes | 9 No |
Answer / karthick
always the fluid flows from high pressure side to low
pressure side.so there will be decrease in temperature and
pressure.inorder to find the properties (pr,temp,vol) of
any gas atleast two parameters must be given.any how if we
take the volume as constant also,temp should be given.
| Is This Answer Correct ? | 0 Yes | 7 No |
Answer / srinivas
i think it as throttling process bcz it is opening through
valve the expansion takes till the pressure reaches to 0.5 bar
| Is This Answer Correct ? | 0 Yes | 7 No |
Answer / phani
the two cylinder are connected by means of a valve so that
total pressure =p1+p2
p1 is first cylinder presu
p2 is second cylinder presure
| Is This Answer Correct ? | 2 Yes | 13 No |
what is the motro?
What is function (in details) room sensor and tube or coil sensor in HVAC system?
IN 6" PIPE IF FEED WATER FLOW IS ABOUT 130 T/H SO SAME DIAMETER OF PIPE HOW MUCH STEAM FLOW SHOUD BE?
what is the difference between pulley and chain???
Is the unit and normal value fuel ratio of an average diesel engine?
What are the causes of dirty lubricating oil?
1: When mesuring the flow of liquid what are the two things to measure? 2: In which industrial process you will use centrifugal separator? 3: If any machinery or transmission needs periodic and regular lubrication what is the best method to give it? 4: Oil melts, grease melts. Is there any other lubrication which is effect at 200 deg c? 5: What is a torque converter? 6: Instead of having individual transmission what is the benefit of unified transmission? 7: What are the different types of mechanism to engage primary moving engine and transmission (in other words how many different types of clutches are there)? 8: In order to ensure constant pressure and constant flow rate of compressed air what should we put between the compressor and end user? 9: What can be the reasons for a metal gasket to leak? 10: The old welding machines used electromagnetic winding to step up the current for welding rods. What is the new principle inside the welding machines?
What is atmospheric pressure?
what is the difference between a boiler and a pressure cooker?
Why should we hire you over the others waiting to be interviewed?
how to calculate air load of a existing/ new plant before installing a air compressor.
i am studying B.Tech 3rd year i want to write group exams. but i don't know about group-1,2,3,4 exams can u tell all the details about group 1,2,3,4 exams and what are the requirements to atttend the exams and how many rounds and what are the subjects we have to look into and what are the posts related to the group-1,2,3,4.
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
