Answer / jeevan dhole

torque is a resistive force producing by rod material about
its own axis when external twisting coupled force is applied
on it.............

moment is the rotational displacement produced by the rod
member about any point on member when external point load or
couple is applied on it..............

Answer / pradeep berry

Pressure is in balloons, pressure is in cylinders, pressure
is active when enclosed,
while Force is push, pull, moving a thing etc.
this is what is naturally happening and will indicate the
difference.

Answer / nayyer

Stress is basically restoring force per unit area.The restoring force is produced on the application of external force, while as pressure is simply force acting per unir area on a surface.

Answer / viplava

stress is internal resistance due to applied load, where as pressure is external force applied upon the surface.
stress may be in tension or compression or shear, pressure is only only compression.

Answer / vivekdoke

pressure and stress both are same
but Pressure is sclar quantity and stress is scalar
quantity e.g Normal stress shear stress

Answer / rajeev mehta

stress always act on solids and pressure always act on liquid

Answer / ravi kumar singh

STRESS is defiend as the ressistance force applied against deformation is known as stress.

but pressure =acting force/unit area

Answer / praveen

Stress deals with the application of load while pressure
deals with the external disturbances or the load.

stress can be stated as:
stress=load applied/Area of cross section

while pressure can be stated as:
pressure=force or external disturbance/Area of cross section

Answer / mj

Stress is tensor whereas pressure is scalar

Answer / engr. safeer khan

stress and pressure are same thing but stress is internal
resistance of solids against applied force
while
pressue is used for liquid and gases which is also an
internal resistance against applied force

How can we find out the weight of metal sheet with the help of its dimensions.

1 Answers  

what is engineering?and what is mechanical engg.?

2 Answers  

A diesel engine,if i use there petrol fuel,What is problem there & what is the result?

6 Answers   TATA, Tata Steel Limited,

what is carburateer

9 Answers  

What are various types of brakes?

0 Answers  

Define monochromatic emissive power. [Ebλ]

0 Answers  

Which material can be used for "wearing pad" used for sliding?

4 Answers  

What is the diffrent between centrifugal and positive displacement pump

4 Answers  

2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand

0 Answers  

mahindra & mahindra's technical & aptitude questions

2 Answers   MAHINDRA, TATA,

• What qualities do you look for in a boss?

1 Answers   Petro Star Mount,

what is a full form of UPVC & CPVE?

2 Answers   Solitaire Builders,