Answer / sriram sarma

Starter is used for a motor to limit the high starting
current. During starting of a dc motor high current of upto
4-5 times the full load current occurs which is avoided by
use of high resistance slowly cut out of the circuit.

Answer / deepesh k v

Starter are basically used to reduce the starting current.
I = ( V - Eb ) / R.
Where I is the field winding current,
V the voltage and Eb - Back up emf and R the winding resistance.
During starting Eb = 0, and R - a very small resistance.
so, as the high current passes through the winding, there is
chance for winding to burn out. When the motor attains the
normal speed it generate the back up emf, enough to reduce
the winding current.
To avoid this we need to reduce the voltage(V) or increase
the winding resistance. Since the reduction of supply
voltage is difficult to attain, a starter is used, which
will push high resistance during starting and gradually
reduces and fully removed from the circuit when the motor
attains the full speed.

Answer / siva

starter used to reduce the starting current of the motor.
and to safe the motor winding in the high starting
current.different type of starter used to the motor. i.e, 3
point starter,4 point starter used to d.c and a.c motors.

Answer / sabyasachi kanungo

generally the resistance of armature is very small i.e in
term of .05ohm or like this.this is due to reduce the
losses.if the motor is connected direct supply high current
will flow and it may burn the armature winding.thats why
starter is connected between supply and motor which reduces
the starting current and provided smooth operation

Answer / saravanan

it is used to reduce the starting current while starting
the motor

Answer / rakesh kumar behera

Electrical starters are generally used to limit the sarting current of the inputed voltage to any d.c. motor. when voltage supply is given to a d.c. motor the current is so high that it can burn the armature windings. So to avoid this dammage we generally use a starter. 4-point starters are used to control the starting current of a d.c. compound motor.

Answer / anup maheswari

starter is used for a motor because at the time of starting
the armature current flow is very high .So,in order to
minimise the flow of high current,starteris used which is
connected in series with the resistance.

Answer / dimpal

intially motor starting current is very high. its 4-to 5
times of the rated current value. its higher value of the
cuarrent burs the winding of the motor so reduce the
startig current value we put the starter.starter function
is intially high resistance in the circuit so current its
reduceand we provide the protection.

Answer / phani chavali

consider a 3phase induction motor,it is a selfstarting
device.Eventhough it is a selfstarting one we are connecting
this device to starter because if we can not connect this
motor to stator because of sudden flow of currents in the
rotor windings some damage may takes place to the machine.so
we can start up the motor with starter means we can limit
the currents to certain value upto which the rotor gets
accelerated.When ever rotor attained its rated speed then
there is no problem of current flow.

Answer / ram

Starter is used for a motor to limit the high starting
current. During starting of a ac motor high current of upto
4-5 times the full load current.and then start/stop switch
on the motor

In AC Drives How can change & control its output Frequency?

5 Answers   Jindal,

what are the safety measure & controls in engine?

2 Answers   RRB,

In an panel board if the outgoings are power plugs and motor equipments...what should we choose as the incomer of the of the panel board?? MCCB OR ISOLATOR?? Should we use ELCB protection??if so where??

2 Answers  

Who are the manufacturer for Nitrogen based Fire Protectio/explosion prevention for Oil Filled Transformers? India and international both?

0 Answers  

How to synchoronize the generator (with gcb,GT) to grid????? ????? from Grid iam getting power (rated 400kv/20kv) through GT and its goes to UAT.,,ST.,, now my generator(rated 20kv ) ready.,, now iam closing my GCB.,, in GT iam suddenly giving 20kv on that Gt.,, what will happend

0 Answers  

How magnetic balance test of single phase transformer is done,Especially in ESP transformer rectifier set.

2 Answers   Bhel,

In which of the following case, the rotating magnetic field is reversed? A regenerative breaking B plugging C dynamic breaking D forward motoring

0 Answers  

in the farm,water tank of 8000 litter capacity situated in 12 meter above.Farm owner want to lift 7000 litter of water within 7 minute to water tank of 12 meter above.which motor having HP rating is suitable for pumping??

1 Answers   ABB, Anchor, Havells, Keltron, KSEB, L&T, vguard,

Why grounding is generally done in supply end?

1 Answers   ISRO, OFBL,

what is the full load current and power rating of 1 Tonne Air Conditioner?How will Calculate?

2 Answers  

for a 11kv transmission line what capacity of CTs & PTs are required?

4 Answers  

What is the difference between earthed and unearthed power cable.

1 Answers