CHEMICAL ENERGY BALANCE - EXAMPLE 11.4 : Calculate the bubble temperature T at P = 85-kPa for a binary liquid with x(1) = 0.4. The liquid solution is ideal. The saturation pressures are Psat(1) = exp [ 14.3 - 2945 / (T + 224) ], Psat(2) = exp [ 14.2 - 2943 / (T + 209) ] where T is in degree Celsius. Please take note that x(1) + x(2) = 1. Please take note that y(1) + y(2) = 1, y(1) = [ x(1) * Psat(1) ] / P, y(2) = [ x(2) * Psat(2) ] / P, * is multiplication. P is in kPa.

1 Answers  

---

BIOCHEMICAL ENGINEERING INSTRUMENTATION - EXAMPLE 29.5 : The following formula is used as a reference : (analyte signal) / (internal standard signal) = (f-factor) x (concentration of analyte) / (concentration of internal standard). A solution containing 3 mM of analyte and 4 mM of internal standard gave peak signals of 2 and 3 mamps respectively. Another similar solution containing 2 mM of analyte and 1 mM of internal standard gave peak signals of 1 and 4 mamps respectively. Find the average f-factor.

1 Answers  

---

What compounds are responsible for the odours that come from wastewater treatment plants?

1 Answers  

---

i have done B.TECH in che.tech.and doing MBA . why you doing mba why u have not join any job.

0 Answers   IBM,

---

Why is post-weld heat treatment sometimes necessary for welded vessels?

0 Answers   Aramco,

---

---

What is the maximum permissible Earth to Neutral voltage in an electrical system.

0 Answers  

---

Anyone please tell me the relation between the m3/hr and kg/hr??...there is some relation to find volume??.

8 Answers   Reliance,

---

What are some good estimates for heat transfer coefficients for coils in tanks?

0 Answers  

---

Question 70 - According to Adolf Eugen Fick (1829 - 1901) : rate of diffusion v increases with less wall thickness t, increased area A and decreased molecular weight of a fluid M. The diffusion constant D decreased with increasing M. (a) By assuming v, t, dP, A, M and D changes proportionally of each other, find the equation of v as a function of t, dP, A and D. (b) The ratio of self diffusion constant D, at T = 273 K and P = 0.1 MPa, for gases B and C are 1.604 : 0.155. If only 2 gases exist in such a system : hydrogen and nitrogen, find the type of gas for B and C with reference to their molecular weights M. (c) By using the equation of kinetic energy 0.5 MV = constant where V = square of v, find the ratio of V for B and V for C, or V(B) / V(C), as a function of M(B) and M(C), where M(B) is molecular weight of B and M(C) the molecular weight of C : Graham's Law of Diffusion.

1 Answers  

---

how interstage pressure of multistage compressor is calculated?

2 Answers  

---

CHEMICAL ENERGY BALANCE - EXAMPLE 11.3 : For liquid benzene, the CP constants are : a = 129440, b = - 169.5, c = 0.64781. Reference temperature is 298 K. The temperature of benzene is 60 degree Celsius. Calculate the enthalpy of benzene by using the formula H = a (DT) + (b/2) (T^2 - TREF^2) + (c/3) (T^3 - TREF^3) where ^ is power, DT is temperature difference with TREF = 298 K. H is in J / kmol. DT = T - TREF.

1 Answers  

---

QUANTUM CHEMISTRY AND CHEMICAL ENGINEERING - EXAMPLE 31.4 : In a rigid rotor model in quantum chemistry, the moment of inertia I is given by an Equation E as I = Ma x La x La + Mc x Lc x Lc = m x L x L, where m = (Ma x Mc) / (Ma + Mc) and L = La + Lc, m is the reduced mass, Ma is the mass of a, Mc is the mass of c, La is the radius of a from point O, Lc is the radius of c from point O. Prove by simplest method that Equation E is wrong.

1 Answers  

---