Which of the following connection is best suited for 3-ph, 4
wire system
A delta-delta B star-star
C delta-star D star-delta

Answers were Sorted based on User's Feedback



Which of the following connection is best suited for 3-ph, 4 wire system A delta-delta B star-sta..

Answer / sunil

(C)In a distribution system, delta-star is best suited

Is This Answer Correct ?    20 Yes 3 No

Which of the following connection is best suited for 3-ph, 4 wire system A delta-delta B star-sta..

Answer / sourabh

Ans: delta star
In 11kv/440v STEP DOWN TRANSFORMER primary side 3 WIRE{LINE WIRE'S (R,Y,B)} ARE THERE DELTS WINDING USED BUT IN SECONDARY SIDE 4 WIRE{3 LINE WIRE'S (R,Y,B) AND 1 NUTREAL} 120*3=360 angle.

Is This Answer Correct ?    4 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

in a diesel generator is there any relation between AVR to fule system?

2 Answers  


How much kv gas generator is needed to run 2 hp and 1 hp airconditioners, plus a refrigerator and 4 Tvs

1 Answers  


Can I use distributon class/transmission class Lightning arresots for protecting the building? If not why please explain?

0 Answers  


SAY CORRECT DEFINITION... WHAT IS EDDY CURRENT LOSS? WHAT IS HYSTERESIS LOSS?

4 Answers  


what does happen if generator frequency fall in running condition & what should require immediately

4 Answers  






i want wipro vlsi placement pattern please send me

0 Answers  


we have one pumping station and 4.6 MW 7 no.s synchronous motors.so there is no required HT capacitor to improve power factor.But we have two no.s of 25 Mva power transformer connect to distribute the power for motors connect with 220 kv line.So i have required the HT capacitor to improve power factor at HT side i mean power transformer bus side.So please suggest how much HT capacitor banks required for same.

1 Answers  


What are the main factors to be considered(In terms of energy conservation) while selecting a new air compressor?

1 Answers  


How do we arrive at selecting reactive capacitance value as 30% of h.p rating of motor?

0 Answers  


if a damaged 500kva transformer with %impedance 2.6 is replaced by two transformers of 250Kva with different % impedance will they be able to catter the load. what will be the ratio of load on the two transformers if the % impedance is in the ratio 1:2

2 Answers   Siemens,


what is the Excaste meaning of CT Saturation?? 10 P 20, 15 VA, what is the meaning of 10, & 20. if the CT polarrity changed what will happened?? what is the differece between measuring CT & Protection CT?? what is the Saturation Point of measuring CT & Protection CT??

1 Answers  


what is iron loss?

4 Answers   RRB,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)