Answer / jayesh r. vasani

As per 'K' type thermocouple coversion chart for 30 mV 721 degree C+ 27degree C (Assume atmosphere temp. Is 27 degree C)so for 30 mV temp. Is 748 degree C.

Answer / sushil jambhulkar

THERMOCOUPLE TEMP = (T/C OUTPUT IN mV * 25)+ atmospheric
temp.
suppose thermocouple out put is 30 mv
30*25 = 750+atmospheric temp.(suppose30deg.cent)
= 750 +30
=780 is the t/c temp.

Answer / malik ashraf

in k type thermocouple..we read 24 degree centigrate againt 1 mv..this is the siple way to find temp.
if thermocouple show 10 mv.its mean the temp is 240 degree c

what is the use of impulse line in AFBC boiler , WHY WE CONNECT IMPULSE LINE TO TRANSMITTER , DRFT GAUGE ETC ????????

6 Answers   Jindal, Reliance,

---

how to connect 3 wire 4-20 mA transmitter in Plc system PLC system and how explain how the measuring data communicate with plc system.

1 Answers  

---

what is plc?

27 Answers   HPCL, KRL, Noor Company, Petrochemicals, SS Automation,

---

Identification of ss fittings, pilot valves, relief valve.

0 Answers   CCIE,

---

what is effect of specific gravity in differential level transmitter , explain formula related with this .

0 Answers   Flour Tech Engineers (P) Ltd,

---

Tell me about PID Tuning and what is PID.

4 Answers  

---

1.what is the effect of vapour presuure in orifice plate flow measurement 2.which is more effective 2 pressure sensors or one single differential pressure sensor in orifice plate measurement 3.how to design a v/i converter and i/v converter 4.how many type of thermocouple are there 5.how many leads are there in thermocouple measurement 6.how pressure sensors are connected in level measurement in differential pressure method 7.what is the output of capacitive pressure sensor (ac or dc),how its o/p is signal charactarized 8.what is the physical meaning of discharge coeeficient,why it is calculated,orifice plate what is its value,why it is less than 1,Q at upstream is equal to or not equal to Q at downstream of orifice plate why?what is vena contracta in orifice plate 9.why rotameter is called variable area flowmeter,it can measure flow even if area is not varying,why it is made tapered 10.design a 10 bit counter ,which counter you will prefer 11.how to remove self heating error in RTD 12.which is more sensitive pt100 or pt50 13.why thermocouple are connected in parallel 14.what is lead contact error in RTD,how to avoid 15.what is P,PI,PID,PD controller,why there is no ID controller 16.what is override,split range,sequential,ratio,feedforward,cascade controller 17.why we moved from SR to JK and then JK to master slave JK flipflop,give correct reason 18.how to measure level of a closed container which contains vapour and liquid,remember no vapour gas should be leaked,so ultrasonic and capacitive is not an option,design another method 19.how to design horse race counter including sensors and signal conditioning element 20.what is bevelling

0 Answers   BARC,

---

pls suggest suitable MOC of diaphragm for pressure measurement of UREA grade solution service fluid.

0 Answers   Siemens,

---

Why 1-5 vdc a standard?

1 Answers   Process Control Technologies,

---

What is the difference between relative vibration

4 Answers   Desein,

---

What is a PID controller and how can it to applied to our everyday life?

4 Answers  

---

the pump holds on run indication into the dcs and filed local control panel remote push button condition operaton wrong like when the push button pushing conditions the pump is off and the push button release condition the pump is on totally opposite condition . And control room inside give the stop command into dcs just 1secon relay engage and again normal condition. How can I slove

0 Answers  

---