Answer / pavan kaneria

Inner Dia of bearing is
Last two Digit Bearing number X 5

Answer / t.c.patil

Last two digit of bearing number shall be multiplied by 5
which is a shaft size.

Answer / rapeti hari hara kumar

1. What is mean by 6205 ZZ

a.6 is the type code, which shows it is a single-row ball
bearing, 2 is the series, means light, 03 is the bore, which
is 17 mm and ZZ is the suffix meaning double shielded bearing.

________________________________________
First two Digit from left indicates bore dia i.e 03 - means
17 mm bore diameter
third digit indicates series like heavy, medium light &
extra light duty - load carrying bearing here its medium
capacity bearing
Last or forth digit shows types of bearing here its Single
row ball bearing
ZZ indicates double shielded bearing


Here is some information on bearing types and nomenclature
that I thought
everyone might enjoy. If you know the bearing number, you
don't need to go to
the dealer, just go to a local bearing distributor or a
place that sells gear
boxes. They should have them or be able to get them in a day.

A bearing number has four parts to it which includes four
numbers and a set of
letters. Each of the first two numbers stand for something,
the last two
designate size. The letters dictate the variation of the
bearing. These letters
can also be followed by more letters designating internal
clearance. In detail:

First number (will be a 1-7) designates the bearing type:
1 = Double Row self-aligning
2 = Double Row self-aligning (wide)
3 = Double Row
4 = Angular Contact
6 = Single Row Deep Groove
7 = Angular Contact

The second number designates the series, or cross section.
This is basically
equivalent to the second number of a tire rating, it's a
ratio of the bore to
the width of the bearing, which also controls the O.D. of
the bearing. The
larger the cross section, the larger the O.D. of the bearing.
18 = Thin Section, Light
19 = Thin Section, Medium
0 = Very Light
2 = Light
3 = Medium
4 = Heavy

The third number (which is a set of two numbers) indicates
the bore (in mm) of
the bearings. All bearings are designated with metric
standards, not inches.
Numbers are as follows:
00 = 10 mm
01 = 12 mm
02 = 15mm
03 = 17 mm
For 20-480mm bore bearings: Last 2 digits x 5 = Bore (mm)
i.e.- if the bearing number was 04 (04 x 5 = 20 mm), 05 (05
x 5 = 25 mm)

The letters after the number indicate the variation. These
change from
manufacturer to manufacturer, but here are some of the
common ones:

Plain -- No Shield
Type Z -- One Shield (normally will have metal shields)
Type 2Z -- Two Shields (one on each side)
Type RS1 -- One Seal (normally the R indicates rubber)
Type 2RS1 --Two Seals (one on each side)
Type LL -- Two Seals (just another manufacturer's designation)
CD -- 15 degree contact angle (for angular contact)
ACD = 25 degree contact angle (for angular contact)

The bearings can also have a C2, C3, C4 or C5 designation
after the bearing
number. This indicates that the internal fit (the inner race
to ball to outer
race) is not standard. If your bearing has one of these
designators, make sure
you get a bearing with the same designator. A C2 is less
than standard
clearance, while a C3, 4, and 5 are larger than standard.

Answer / hanif

Ball Bearing 6301

Answer / stephen martey

The last two digit multiply by 5 (05×5=25 which is inner diameter 6 is the code and 2 is the light,and zz is double shielded

Answer / hari

it will vary from ID to ID( means up to 10 it has direct
value after 10 mm dia it has caliculation of last two digits
multiply by 5

Answer / sonu manna

Baring code numbar formula detals

Answer / md.billal hossain

my need chart of bearing number according to inner diameter and outer diameter.if possible the bearing number formula please send me my email adress

Answer / abin

The outer dia of a bearing & the searies eg:6205 .enithing relationship ? Plzz answer
Id is Abinoxy@gmail.com

Answer / rahul

6205

when do we use roller bearing, deep groove ball bearing, angular bearing, sealed bearing, semi sealed bearing, unsealed bearing, anti friction bearing, journal bearing, thrust bearing

0 Answers  

What are the objectives of NVH (Noise Vibration and Harshness) analysis?

3 Answers   BARC,

• Explain about your dream job.

1 Answers   Petro Star Mount,

what is the equation of drag coeficient?

0 Answers  

what is the difference between the air preheater & air blower?

4 Answers   Castrol,

what is the difference between high speed and a low speed turbine and on what parameters we will chose or go for either low speed or high speed turbine...

2 Answers  

what is the equation to find out of full vollum of cylinder ?

2 Answers   Kuwait Oil Company,

DOES IS 2062 SPECIFIES ONLY SEAMLESS PIPES OR ERW PIPE IS ALSO COVERED UNDER IS 2062

0 Answers  

eligibity for TNPSC group 1 exam , age limit

0 Answers  

Define reynolds number [re].

0 Answers  

How to operate soot blower boiler and economizer?

0 Answers   ABC Inc, RRB, Siemens,

What is the difference between tube and pipe?

0 Answers