Answer / jsindrajit

Drum level is measured by measuring the differential
pressure accross two tapings(Bottom & Top)in the drum by
using DP transmitter, whose HP side is connected with the
Taping coming from the bottom and LP side connected with
the taping coming from top.
HP side will have a pressure of Both the Steam Pressure and
Water Level. At the same time LP side will have only Steam
Pressure. Therefore the transmitter will reflect only the
Water level.
The range selection for transmitter depends mainly on three
factors i.e. Drum working Temperature, Drum working
Pressure and Difference of pressure between two tapings.
There are other factors also like Dade band, accuracy,
repeatability, response time etc.

Answer / ram

First of all u should be clear about which kind of liquid
level u want to measure? B'coz selection of level
transmitter depend on it. So many x'mitter are available
with different types and range according to the application.
And range is depends on ur drum size.

Answer / george mathews

if we are trying to measure the drum level of a drum which
contain water or (H2O) we prefer to use the Hydrastep .
Which is in my knowledge one of the trusted sencer of it
kind .

Anather by using the pressure or more preciesely the DP
transmitter. Here what we do is , we take the connection of
the higher end of the DP Transmitter from d bottm of the
drum and simulteneously we take the connection form the
upper end .where we can find the difference and calculate
the level of water it has got. as during the time of
calibration it is being feeded what ll b d pressure of the
drum when it is full and what is the pressure when it is
empty .
so it ll differenciate the difference between the actual
lever of water level of the drum.

Here the key factor is the density of Any medium , once we
know the Exact density of the Medium we can find the level
easely with the DP Transmitter.

Regarding , there is an air cooler which control the fans(50% of AV FANS) by temperature in outlet , and the louver of Air cooler is controlled by HIC from control system , So if on Air cooler we will consider 2 individual I/P converter or positioner?

0 Answers   Chagalesh Consulting Engineers,

---

there are two candidates p and q in an election.During the campaign,40% of the voters promised to vote for P ,and rest for Q.however, on the day of election 15% of the voter went back on their promise to vote for P and instead voted for Q. 25% of the voters went back on their promise to vote for Q and instead voted for P.suppose,P lost by two votes,then what was the total no. of voters.

1 Answers   GATE,

---

what is the advantage of submersible level transmitter compare to ultrasonic level transmitter?

0 Answers  

---

what is difference between 3 wire and 4 wire RTD sensor?

12 Answers   HTA Instrumentation,

---

What is the procedure of mounting new positioner on pneumatic control valve?

1 Answers  

---

why we use by pas on a positioner? When can a by pass be not used on a positioner ?

2 Answers  

---

Dear Sir/Madam, I am attending an interview for ETs in BHEL. I have cleared my written test under Electronics (Instrumentation). This is the first time I am appearing for an interview. Can any one who has attended the interview earlier give me a clue to face the interview. With regards Sindhu

2 Answers   Siemens,

---

Someone please do mail me some instrumentation questions for Hindustan Petroleum test to avinalexander@gmail.com .Really would be gateful if someone could help me

3 Answers   HPCL, Immersion, IOCL,

---

Exothermic reaction./ endothermic reaction

0 Answers   CCIE,

---

Can we use twisted pair cable instead of ethernet for communication?

1 Answers   Yokogawa,

---

what is the advantage by using PID controller than P& PID?

1 Answers  

---

how can use ram

0 Answers  

---