Answer / srinivasa rao talasila

Star connected or star running designed motor winding
resistance is some what high compared to delta running
designed motor.

Exambple 5.5KW star designed motor is having a resistance
of 1.2 ohams,same in delta is 0.45 ohams like that

Not exactly the same but there is a difference in
resistance.

Answer / k.prakashchandra

If it is LT motor and 3 wires are coming out, it is delta
connected . If there are 6 wires it is neither delta nor
star ,which is decided by starter which connects windings in
star at starting and then in delta afterwards.

Answer / gunasekaran

for LT motor if we want more power output it should be delta.for HT motor mostly it should be star connected.some special purpose motor will be delta not all in HT.

Answer / goutam roy

In case of star connection, you can have 4nos. Of wire. 3 wires for 3 phases and other for neutral wire (very important for protection) in case of del. Connection you can have 3nos. Of wire. (This connection is very important for arresting harmonic f)

Answer / surender k

Motor star/delta connection = feed by two cable of suitable
core & size.
Motor delta connection = feed by one cable of suitable core
& size.

or

Its application area and load parameters like water
lifting,air-fan in large buildings.

Why one side of secondary of transformer is earthed, to supply single conductor of electric traction system?

1 Answers  

---

How to calculate transformer capacity requirement for a project site?

5 Answers   ABB,

---

what is the differents and advantages of Electro magnetics relay and static relay ? what is the numerical relay ? advatages?......

7 Answers   CAT, L&T, TCS,

---

AC voltage only create magnetic flux in coils, but in Solenoid coil how 24V DC volt create flux and pick the plunger

5 Answers  

---

why motor rating in KW?

2 Answers  

---

---

what is the cause of voltage dipp or swell in the transmission lines?

0 Answers  

---

In transmission line the line power loss only accured at resistance the inductance and capacitance wont consume power is it correct?

2 Answers  

---

What will be the output voltage of a transformer if it is primarily energized from a square wave voltage source?

0 Answers   HPCL,

---

what is buscoupler adopter panel????

5 Answers  

---

What is maximum permissible length of cable from transformer (33kV/0.433kV) HT side to HT panel which contain VCB? In which standard i shall get this information.

6 Answers   MSEB,

---

1- XC and the RC time constant are both measures of the reaction of C to a change in ____? 2-The power factor is a numerical ratio with a value between 0 and 1 equal to the ______________ of the phase angle. 3-When V and I are out of phase because of reactance, the product of V times I is called ______________ power 4-For _____________ inductors, the branch currents can be added algebraically. 5- The ______________ power in watts can be calculated as I^2R 6-Calculate XL with L = 30mH and f = 1kHz ( I have Xl=2piFL 2*3.141592653*1kHz*30mH =188 ohms Please check) 7-A parallel RL circuit has the values, R = 5kohms, XL = 5kohms. A voltage source of Vt = 10Vrms is connected in parallel to R and L. Determine the total current, It delivered by the voltage source Vt. 8-A series RC circuit has R = 1Mohm and C = 1microF. How long would it take for the capacitor to fully discharge if it is initially fully charged? 9-A circuit has real power = 300W and an apparent power of 500VA. Determine the power factor and phase angle. 10-The time constant for an LR series circuit is T = 0.1s and R = 10ohms. Calculate the inductance L.

0 Answers  

---

Normally the starter used to reduce the starting current.but the dol starter do not it,so why we use it?

4 Answers  

---