what is the difference between sinking and sourcing inputs and also what are t

what is the difference between sinking and sourcing inputs
and also what are there applications?

Question Posted / samarthchaturvedi

2 Answers
6332 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

what is the difference between sinking and sourcing inputs and also what are there applications?..

Answer / shilpa.p

SOURCING means the device which delivers current to the load.
SINKING means the device which draws current from the load.

Is This Answer Correct ?

16 Yes

3 No

what is the difference between sinking and sourcing inputs and also what are there applications?..

Answer / keyur

main application of sink and source is to control of direct current flow in load.
DIfference b/w sink and source is
SINK MODE provide a path to 0V DC (-DC)
SOURCE MODE provide a path to +24V DC (+DC)

Is This Answer Correct ?

9 Yes

1 No

Post New Answer

More Instrumentation Interview Questions

units of pressure,flow, level,temperature? principle of pressure gauge? calibration of pressure tx., level tx., temperature tx.flow tx.? description of two wire ,three wire and four wire R.T.D.? WHAT IS INPUT AND OUTPUT OF TX.? WHAT IS INPUT AND OUTPUT OF R.T.D. AND THERMOCOUPLE? WHAT IS HOT LOOP AND COLD LOOP? WHAT IS INPUT AND OUT PUT AND OUTPUT OF D.C.S. AND P.L.C.? PRINCIPLE AND WORKING OF HART? WHAT IS PNP AND NPN PROXY? CALIBRATION OF PRESSURE ,LEVEL ,FLOW SWITCH? DESCRIPTION OF FIELDBUS FOUNDATION? WORKING OF SOV.?

2 Answers

What is the diffrence between ff tx and non ff tx

0 Answers Jindal, Rosemount,

What is the difference between dry contact and wet contact?

2 Answers

what would be the minimum flow rate that we can measure on rotameter..?

0 Answers TATA,

i have done DAE in Instrumentation and Process Control. i have applied for an apprentice training in chemical company after three day my interview will be conduct but i need more information about industrial process control and controller. my e mail is imran_dilsetu@yahoo.com please tell me interview question relative to instrumentation ?

0 Answers

I have a Control VAlve having size of 2 ".Only the known parameter is Pressure drop . Its 2 Kg. Then How to calculate control valve sizing means Cv.

0 Answers JSW,

Why we use negetive (-)voltage in vibration system

4 Answers

What is seeback effect?

3 Answers

What is difference between flame retardant & flame resistance cable? Among which type of cable is used for ESD & Fire and Gas system application?

1 Answers

1. what is 3 point calibration & 5 point calibration? 2. If we use hart communicator to set the LRV & URV of a smart transmitter, did we calibrate the transmitter? why? 3. Make a complet list if meterials needed to properly connect a pressure gauge to a steam pipe using 1/2 inch stainless steel tubing. The gauge connections is 1/2 inch NPT-M and the steam pipe tap has a 1/2 inch female coupling, compression fittings are use. 4. What are the tools in loop checking? 5. What would the ISA symbol of a square root extractor look like? 6. What would you do to completely prepare for the configuration? 7. What safety measures must you undertake when doing configuration? 8. what are the two most commonly use programming languages used when we configure a PLC? 9. What would you do if you accidentally skipped a step in the configuration procedure? 10. How would you know if the configuration were sucessful? 11. Name at least 3 selections available when we configure the burnout protection of a controller?

3 Answers EI Electrotechnical Institute,

what are the problem's will accure in dcs or plc hadware and what are the solution for it?

2 Answers

If mVolts can drop by resistance of wire as compare to mA, then how thermocouple mV reaches in CCR as accurate value?

7 Answers

For more Instrumentation Interview Questions Click Here