Answer / aaditya

Draught means force needed to draw.with regard to the boiler the requirement is to supply adquate amount of air to grate for proper combustion to draw the resulting gas from the system and discharge this gas from chimney to surrounding it requiresa static pressure difference which causes flow of air and gases to take place. The static pressure difference maintained is called is called boiler draught.

Answer / trinanjan bhadra

It is the supply of sufficient air through the boiler grate for efficient combustion of fuel...Drought is 2 types.....there are. 1: NATURAL DROUGHT & 2: ARTIFICIAL DROUGHT....thats it....

Answer / parth chaudhary

Draught in Boiler chimney is Induced Draught which is
generated by induced draught fan.
This Fan is mounted after Esp(Electro static precipitator)
and Before Chimney.
Is Funtion is to suck Flue Gas from Boiler , Esp & Flue gas
duct to chiney.
This draught is manual one.
While the natural draught is created by temprature
difference between the flue gas inside the chimney and
outside the chimney.
Hence the Pressure difference is generated.
hence Flue gas Tend to move Upward.
from hight to low temprature.
more over Pressure inside the chimney is more than
atmospheric pressure hence it moves outward.

Answer / pramod nair

Draught is the pressure difference between boiler furnace and stack. which is Providing to flow the flue gases to chimney other wise flue gases will come out through manhole or any openings. So always draught is a negative pressure.In a balance draught forced draft is providing before furnace and Indused draught is providing after furnace.

Answer / aditya meshram

A small static pressure difference which cause a flow of gas to take place is termed as a draught and its function in case of boiler is to force air to the fire and to carry away the gaseous product of combustion.
There are two types of draught: 1. Natural draught
2. Mechanical draught

Answer / vishal gavit

The draught is one of the most essential system of thermal power plant which supplies required quantity of air for combustion

Answer / sanjay singh

Drought is the pressure difference which is necessary to flow fresh air into the combustion chamber the boiler.

Answer / rahulsom

I.D fans is use only sucks the flue gas and ash and these sent in atomsphere.

Answer / arun

draught is the pressure differans between the boiler furnace grate and outlet of the chimny
used to full combustion of fuel and flow of flue gases

Bearing no : 6402 what is the ID ,OD,width

0 Answers   ABC, SRACO,

what is the viscosity of hydraulic oil?

1 Answers   ONGC,

mahindra & mahindra's technical & aptitude questions

2 Answers   MAHINDRA, TATA,

How is the aptitute test done

0 Answers  

tell me 1 name of device where work & heat transfer is -ve

2 Answers   Chandan,

What are the benefits of cycloidal gears?

0 Answers  

2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand

0 Answers  

The ratio of Emissive to absorption power of heat by a body is equal to heat emitted by a perfect black body. Who said the statement

3 Answers   HAL, ONGC,

What resistance the ship encounter when the vessel is at sea

0 Answers   RRB,

What is the least count of micrometer

5 Answers   Alfa Laval,

Properties of F.O. the cause damage on auxiliary boiler.

0 Answers   RRB,

Hello . pls tell me ..when the results of HPCL officer trainee exam held on 2nd march 08 are coming out...any guess?? pls reply

1 Answers