Answer / rajesh

wat the bleddy answer ...if u dont know u shouldnt post tat
worst answers.....
nw see answer...
its nt 5 degrees dear tat 11 means it resembles 11 o clock
in a wall clock tat means it makes 30degrees.......
so tats it ther is phase between primary and secondary of
30degree
THIS IS A COMMERCIAL NOTATION OF TRANSFORMER

Answer / anil

the first letter must be capital one, which represents HV
winding while second letter should be lower case, which
represent LV winding of transformer.
1. 'D' - HV winding is delta connected & 'Y'- HV winding
is star connected
2. 'd' - LV winding is delta connected & 'y'- LV winding
is star connected
And rest of number indicating phase displacement angle
i.e 1 = 30°, 2 = 60°, 3 = 90°, 6 = 180° and 12 = 0° or
360°.

so
Dyn11 indicates,
Delta connected HV winding, star connected LV winding with
neutral brought out, LV is leading HV with 30°

Answer / meenakshi

i agree vid anil...to b more specific,Phase rotation is
always anti-clockwise. (international adopted convention)
we use the hour indicator as the indicating phase
displacement angle. Because there are 12 hours on a clock,
and a circle consists out of 360°, each hour represents
30°.
Thus 1 = 30°, 2 = 60°, 3 = 90°, 6 = 180° and 12 = 0° or
360°.
The minute hand is set on 12 o'clock and replaces the line
to neutral voltage (sometimes imaginary) of the HV winding.
This position is always the reference point.
Because rotation is anti-clockwise, 1 = 30° lagging (LV
lags HV with 30°)and 11 = 330° lagging or 30° leading (LV
leads HV with 30°)

Answer / virender s negi

I correct my self it is a 30 degree phase shift.

Thank's rajesh for your inputs.

Answer / virender s negi

DYn11 Means D=Delta, Y=Star, n=neutral, 11= 5degree phase
shift. This means there is a phase shift of 5 degree from
primary to secondary of a transformer.

1.what is difference between ATS & STS main use. 2.what is difference between ACB& VCB With symobles,and main partes, manimum range. 3.How many types of relays and main function.

0 Answers   Visa,

power is the product of voltage and current.so we can measure the value of power just by using ammeter and voltmeter.......then why do we use a wattmeter?

5 Answers  

Why we have use 3 & 1/2 core cable use for general electrical supply arrangement

1 Answers  

please send privious years question papers of jindal steel and power ltd.My e mail id is rajanikant.sngh@gmail.com

0 Answers   Jindal,

What do you mean by cogeneration? What its working principle?

0 Answers  

How much costly in percentage wise is sandwich busduct costly than air insulated busduct of any rating?

0 Answers  

while doing high potential for 11KV 3 core cable how much leakage current will obtain?, what will be acceptance value?

0 Answers   Voltech,

How halogen & merquery lamp works.

0 Answers  

in Contactor opearation Why there is a difference in the values of the operate and release voltage in case AC supply

0 Answers  

what is the load amp of a 2 hp single phase motor?

6 Answers  

how could we know the size of cable by physical view?

0 Answers   Havells, United Engineering,

When a square wave is applied to primary of a transformer then what will be output wave form of secondary ?

15 Answers   Bhel, Sail, Sterling Telecom, TCS,