Answer / kumar

it depends on the direction of flow of air. If the room is
closed we may assume that air flow is restricted. But here
it is mentioned that open room. in such case plate hanging
in vertical direction will cool first. becaue generally air
folw will be pridominent in horizontal direction then
vertical. hence vertical hanging palte will receive more
bombartment from horizontal flowing air, and will cool at
faster rate

Answer / mohan

VERTICAL ONE WILL COOL FASTER DUE TO NATURAL CONVECTION OF
HOT AIR FROM THE SURFACE OF THE PLATES ON BOTH THE SIDES...
BUT IN CASE OF HORIZONTAL PLATE, DOWNWARD SURFACE EMITTING
HEAT,THE AIR WHICH GETS HEATED UP CANNOT RISE UP (HOT AIR IS
LIGHTER THAN COLD AIR) SO, THE HEAT DIFFERENCE BETWEEN THE
PLATE SURFACE AND AIR AT BOTTOM IS LESS COMPARED TO THE
VERTICAL CASE, HENCE VERTICAL PLATE WILL COOL FASTER....

Answer / jacky

I think there is a small twist in the question. Normally if
it was a closed room and the plates are stationary then
according to the principle of natural convection the
vertical plate will emit more heat and will cool faster than
the horizontal one. But here its mentioned that the room is
open, so there may be some air flow horizontally too. So the
answer depends on the rate of air flow too. But nothing is
mentioned here. So we cant assume huge air flow. Note that
the natural convection effect is also there. So the more
correct answer would be the vertical plate....

Answer / muralidharan m

First this two plates are suspended in open room,
and we are giving thermal source means automatically will get
heat only.
As per this my suggestion this plates will not get
cool(Weather its vertical or horizontal).

Answer / vivek

I think horizontal one.
Becoz cooling will occur due to natural convection. As the
horizontal plate will have more upper surface, so more heat
will go up in the form of air as it is a law of convection.
so it will cool faster than vertical.

Answer / sujit singh

here since cooling will take place by convection. if the temp of plate is higher than room temp .. heat will flow from plate to room.. thus causing it to cool. heat transfer by convection depends on surface area.. and here surface area exposed to room atmosphere is same in both case... so both will cool at same rate.there is natural convection as we are not using any device to cause the motion of air over plate. so no question of forced convection.

Answer / nitish rai

The plate with the larger specific dimension exposed to air flow will have a higher rate of heat transfer so the plate with HORIZONTAL orientation is cooling through;
FORCED CONVECTION
&
that with VERTICAL orientation with NATURAL CONVECTION

hence Horizontal plate should cool faster.

Answer / akash varshney

nitin is ryt .....see a simple example of .......bike engine
.....fins r used ...n have u ever see vertical fin in ur
bike ,,,never,,,,,,always horizontal......it is air nt a
metal or a solid in which u r seeeing conduction.....bt here
is air n case is fr convection.

Answer / nitish

Dear frnd plate is suspended so there is no point of contact moreover vertical plate will only cool due to natural convection........therefore HORIZONTAL will cool faster.

Answer / vivek

vertical one,since it is in less contact with grond
compartive to others.

How to identify the bearing number with 3 dimensions of bearing ID & OD & bearing outer width? In interview me answerad only the bearing ID multiply with 5. That is last two digit number.

0 Answers   Al Suwaidi, Shriram Pistons, SPIPL,

why can't you use centrifugal pumps for pumping viscous fluids?

3 Answers  

Can you use motor oil in a hydraulic system?

0 Answers  

what is unit of mechanical work nand piower ?

5 Answers   Hindustan Unilever Limited,

Which is the hardest material on earth?

0 Answers  

Explain what are the thermal conductivity properties of brass?

0 Answers  

hi,i am sekar.i am prepareing Assistant Motor Vehicle Inspector in TN.Transport ,if any one have previous year model pares or some questions,pls send me at gpsekar2007@gmail.com.

0 Answers  

how to caluculate APFC panel rating, my running Load is 1320KW, Present P.F 0.76 to 0.8 we need 0.98 p.f

17 Answers   Accor, AEPL, Alfa Automation, Jet Airways, Kingfisher, Servo, Spice Telecom, Usha,

Hi i am riyaz ahmed . i got rejected for first time and i nedd to apply for next time and can i apply in 1 or 2 week . and wt abt my sevies fee ? i should make a new once shill i go with the same and wt docement i should change can u plz help me out and my mail it is royalriyaz@gmail.com

0 Answers  

explain the omportance of "squish" and "swirl" in ci engine

0 Answers  

what are the essential things for the power plant

1 Answers   NEPC,

DRAW REFRIGERATION CYCLE? WHICH REFRIGERANT USED IN IDUSTRY & HOME? EOT CRANES SPEED ? WHAT IS KOM ? TELLL ME ABOUT YOU? WHAT WAS YOUR FAVORITE SUBJECT?

3 Answers