Interested to Buy Any Domain ? << Click Here >> for more details...
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
Why is the electric shock from the DC supply is more dangerous than the shock from AC supply.
IBM,
8 12039Two shafts A and B are made of same material. The diameter of the shaft B is twice that of shaft A. The ratio of power which can be transmitted by shaft A to that of shaft B is
5 26924The higest value of thermal conductivity is expected for a.) Solid ice b.) Melting ice c.) Water d.) Boiling water Give the thermal conductivity value for each.
2 4876why the starting voltage drop in a cable needs to be limited?what is percentage of the voltage drop allowed during starting?
1822please send me previous question papers of rrb chennai applied for junior engineer in mechanical dept
2003What is the major difference between P.T. & C.V.T ? Why CVT is used in HT Transmission line in place of P.T.?
13 115333
hi my name is rakesh patel i just complited my be in instrumentation & control now i am going to working as a validation engineer in a poject department so what is a scope in a future as a validation engginer ? what line is good for me can any bady give me complete solution please? your regard rakesh patel
WHY IBM MAINFRAME TECHNOLOY IS USED.THOUGH, SINCE ITS INTRODUCTION IT HAS NO MAJOR UPDATATION OR MODIFICATION;BUT STILL IT IS IN DEMAND........WWWWWWWWWWWWWWHHHHHYYYYYYYY????????????
What is universal motor?
1.How much batten required for 1 sqm Shuttering. 2.how much pipe & clamps required for staging of 100 sqm shuttering at 5.0 m height.
Which is the common element between brass and bronze ?
When we connect the large capacitor bank in series ?
what is the meaning of 5% droop or 7% droop in AVR?
What is a copper loss or i2r loss pc?
What would you do if your captain were not following the instructions properly?
How can claculate to attain the desired PF in the line ( HOW Much KVAR is required ) Pls Give the formula? Equate Petrochemical 0 1 how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec. 0 1 What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding? Equate Petrochemical 0 1 What is required of exietation to the alternater. 0 1 why star point of HT motor not earthed? Equate Petrochemical 0 1 Why we are getting low voltage in star connection? Equate Petrochemical 0 2 What's ND relay & it's functions? Equate Petrochemical 0 2 How instantanious short circuit current is calculated? its formula? Equate Petrochemical 0 2 What is servo Motor? What's the advantages of this motor over Induction motor? Equate Petrochemical 0 2 What is core CT & it's function? Equate Petrochemical 0 3 what is meant by star/delta voltages as 440/220 in a 3 phase induction motor, and why it should be connected on STAR IN 3 PHASE SUPPLY L & T 0 4 What is required of exietation to the alternater. KNB 1 23 what is the design voltage for 6.6KV 2000 KVAR HT capacitor? Consultancy 0 3 Pls explain about vfd control?Where it is used, Give some example? siemens 1 22 Please explain me abt PQ diagaram in the power sector. 0 9
What is the difference between torque and power?
what is method for testing CT
whats is difference between anchorage length and development length
What is the difference between relays and contactor construction wise?
need the type of technical questions in written test
