Hai friends this is Dara s. solanki, i done in B.Sc.(IT) i have an 2.3 years of exp in Manufacturing company in MIS giving support in SAP , 1 year back i did Sap course In MM Module. am trying from the day one to enter into the sap field but i was not.i kindly requesting all, please suggest me how to enter in to the SAP field. Looking for a job . i please help me and having any thing please let me know . i am in bangalore. my mail id is Dara.solanki@gmail.com. 8431455753

1704

how IDP Qury perform by the B subs MSC for MTC call. If subscriber is in roaming in other state? plz explain briefly

2407

what else we can add rather than admixture in concrete to reduce the cement quantity?

5324

A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.

1697

Dear all, I just want to ask an expert on this forum for some insights. For the magnetic balance test, when applied voltage on a Delta-Star transformer e.g. Dyn11, the following relationships apply for HV side: 1.  H1-H2 = H2-H3 H3-H1 2.  H2-H3 = H3-H1 H1-H2 3.  H3-H1 = H1-H2 H2-H3 For the LV side also: 4.  X1-X0 = X2-X0 X3-X0 5.  X2-X0 = X3-X0 X1-X0 6.  X3-X0 = X1-X0 X2-X0 Is there a similar pattern for Y-d, Y-Y, D-d? And how about Y-z, D-z, Z-y transformers? I've tested a YNzn5 transformer and for LV side I don't see the pattern. In this particular case I got for LV side the following (see values below): H1-H0  H2-H0  H3-H0    X0-X1  X0-X2  X0-X3 128.0  119.9  7.2      29.2   13.3   15.8 70.7   128.4  59.2     23.4   22.0   3.6 7.2    120.1  128.1    13.4   29.3   15.8 What is the relationship here for LV? For row 1 I see the relationship, for row 3 I also see but it's shifted, but for row 2 I don't see such relationship. Any suggestions, answers, someone?

1370

Hai Frds i want to join in testing tools course , plee tel me which was the Best institute, plsss reply me, i am waiting for ur reply....

1454

Hello Friends I had my ONGC test today,but it was very bad.But I would give certain suggestions so that u may not face he problem which i had. Be thorough with Electrical Technology.Generators.motors stators etc.There are 5 questions on that. There were also good no.of questions from Hydraulic machine and Production technology. Then 3 from Strength of materials.And remember the dimensional quantities.

1523

sir, i preparing hpcl,ongc,barc,hal exams(instrumentation engg)pls send a placement papers

1876

Explain why gold is added to the p-n junction?

629

Draw the space diagram for a ten meter long beam simply supported at each end?

684

What is the function of auadag in a cro?

684

Why you would like to join the aviation industry?

679

Why do not we prefer non conventional sources of energy to conventional sources?

687

SIR plz send me old exam papers for RRB chennai

2315

what is the theoritical percentage of concrete cubes testing per day?

4395