What capacity say in pumps

Answers were Sorted based on User's Feedback



What capacity say in pumps..

Answer / sumit verma

LPM (litres per minute) or GPM (gallon per minute)

Is This Answer Correct ?    16 Yes 2 No

What capacity say in pumps..

Answer / iitm-pazhanivel

Discharge--It is the ratio of volume of the fluid per unit
seconds

Is This Answer Correct ?    2 Yes 0 No

What capacity say in pumps..

Answer / naveen

horse power like 1 H.P,2 H.P PUMP.......
high head,low head pump,...ie.high pressure,low pressure
pump...ex.5-10 bar pressure....
according to discharge quantity..ex.10lit/hr

Is This Answer Correct ?    1 Yes 0 No

What capacity say in pumps..

Answer / muthukumar

lps

Is This Answer Correct ?    0 Yes 0 No

What capacity say in pumps..

Answer / shah alam

LPH ( liter per hour) for small pump and m3/hr (meter qube per hour) fore big pump.
1 m3 = 1000 liter.

Is This Answer Correct ?    0 Yes 0 No

What capacity say in pumps..

Answer / saravanakumar

hourse power(HP)

Is This Answer Correct ?    3 Yes 4 No

Post New Answer

More Mechanical Engineering Interview Questions

In a Waste heat recovery boiler feed control valve is after the economiser where as in auxilary boiler feed control valve is given before the economiser.why?

2 Answers  


what are the supports using in critial pipe line and what are the type of support using oil&gas, power plant.

2 Answers  


how to calculate a id fan capacity and sutable motor in kw's.i have a fan impeller dia is 1050mm, width is 105mm in impeller inside to inside,and impeller section cone gap is 450mm, impeller plate thick is 5mm,what is the sutable motor and how cen i calculate the fan capacity, tell me the calculations with Exa also.

1 Answers   BPSL, HCL,


• What experience do you have in this field?

1 Answers   Petro Star Mount,


What is extruded aluminium used for?

0 Answers  






Explain difference between fissile and fertile materials?

0 Answers  


What is Dry Bulb Temperature and Wet Bulb temperature?

3 Answers  


We select 10mm nominal thickness for Elip head of a pressure vesel. The minimum thickness after forming is 8.2mm. (Shell thickness is 8mm. The minimum thickness after forming is satisfied or not with UG-79 (d)(3) in ASME SECTION VIII, Div.1?

0 Answers   PetroVietnam,


what is servo motar?

2 Answers   Visa Steel,


difference between statics and dynamics

1 Answers  


Which is more efficient? A rear engine Volvo Bus or a Front engine Volvo Bus? (Engine Capacity is same 4 both) why?

7 Answers   Visa Steel,


THIS IS HARI PRASAD. I KNOW THAT HVAC MEANS HEATING VENTILATION & AIR- CONDITIONING. I NEED DESIGN CONSIDERATION OF HVAC UNIT.

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)