The amount of carbon present in Cast Iron

Answers were Sorted based on User's Feedback



The amount of carbon present in Cast Iron..

Answer / himanshu

Carbon is basically present in the form of cementite in cast iron.Its percentage lies in the range of 2.03-6.67(% by weight of cementite)for Cast Iron.If the amount is less than the above range than it is stainless steel.....

Is This Answer Correct ?    15 Yes 2 No

The amount of carbon present in Cast Iron..

Answer / malayappan

Above 2% of carbon with iron is known as Cast Iron. As per
the Iron-carbon diagram cabon can be maximum to 6.67
percent. However any commercial cast iron will have caron
in the range of 3 to 3.6%. This carbon will be present in
two forms 1. As combined Carbon (Cementite) and the other
one as Free Carbon (Graphite)

Is This Answer Correct ?    12 Yes 2 No

The amount of carbon present in Cast Iron..

Answer / rajeesh

The amount of carbon in cast irons is 2.1-4 %wt

Is This Answer Correct ?    10 Yes 3 No

The amount of carbon present in Cast Iron..

Answer / karthick

minimum 2%

Is This Answer Correct ?    4 Yes 4 No

The amount of carbon present in Cast Iron..

Answer / praveen singh

Cast iron contains 2.1-6.67% carbon
In which 2.1-4.3 % carbon contain Iron is Hypoeutectic C.I while from 4.3-6.67% is hypereutectic C.I and 6.67%c is called Cementide

Is This Answer Correct ?    0 Yes 0 No

The amount of carbon present in Cast Iron..

Answer / adinarayana kopparthi

2% of carbon containe is cast iron.

Is This Answer Correct ?    2 Yes 5 No

The amount of carbon present in Cast Iron..

Answer / plnde

1 to 2

Is This Answer Correct ?    1 Yes 14 No

Post New Answer

More Mechanical Engineering Interview Questions

What is the air flow rate at suction, if impeller of dia 1500mm and it consists of 8 no's vane, running at 1500 rpm? Dia of suction pipe is 500mm.

1 Answers  


where impulse turbine & reaction turbine are used?

2 Answers  


Explain the difference between hydraulic oil and engine oil?

0 Answers  


Difference between turbocharging and supercharging in diesel engines?

0 Answers   VLS,


which actor do u like ?

0 Answers  






what is difference between 1ton to 1HP

2 Answers  


What are mechanical safeties in DG sets?

2 Answers  


What is meant by direct heat exchanger [or] open heat exchanger?

0 Answers  


what is cyclon seperator and water column?

0 Answers  


how to guess size of hole according to size of bolt,say M12?

3 Answers  


What is critical speed in turbine?

2 Answers   SPIE, Sundram Fasteners,


If a dimension is given as SC parameter, is supplier allowed to use full range of tolerance specified in drawing without proving capability?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)