In which layer switch is work?

Answers were Sorted based on User's Feedback



In which layer switch is work?..

Answer / sag6912

Layer 2 ,Data Link Layer

Is This Answer Correct ?    65 Yes 3 No

In which layer switch is work?..

Answer / santosh

layer2

Is This Answer Correct ?    32 Yes 3 No

In which layer switch is work?..

Answer / hum apke hain kaun

layer 2 as well layer 3( what about layer 3 switch)

Is This Answer Correct ?    23 Yes 2 No

In which layer switch is work?..

Answer / guest

switch works in layer 2

Is This Answer Correct ?    16 Yes 0 No

In which layer switch is work?..

Answer / guest

Layer 2

Is This Answer Correct ?    15 Yes 0 No

In which layer switch is work?..

Answer / sk ohab rahaman

Switch works in layer 2, but there are some special switch
can operate on layer 3 also.

Is This Answer Correct ?    9 Yes 0 No

In which layer switch is work?..

Answer / siddhesh vaze

layer 2 , in data link layer

Is This Answer Correct ?    5 Yes 0 No

In which layer switch is work?..

Answer / guest

layer 2

Is This Answer Correct ?    5 Yes 0 No

In which layer switch is work?..

Answer / guest

data link

Is This Answer Correct ?    5 Yes 1 No

In which layer switch is work?..

Answer / ajay

below 3600 series switches are layer 2 device and above 3600
series switches are layer 3 & 2 device.

Is This Answer Correct ?    4 Yes 1 No

Post New Answer

More CCNA Interview Questions

What command do we give if router IOS is stuck?

0 Answers  


Which statement about Ethernet switches is true? A. Symmetric switching allows connection between pods of unlike bandwidth and does not require memory buffering B. Memory Buffering is used to prevent a bottleneck when pods of different bandwidth are connected on a symmetric switch C. The latency can be reduced if the switch utilizes the store and forward method of switching store and forward is better for error detection D. The cut through method of switching is faster because the switch forwards the packet to the destination as soon as it reads the destination address

1 Answers  


On which base distance vector choose best path?

0 Answers  


Which router command allows you to determine if an IP access list is enabled on a particular interface? A. Router# show ip interface B. Router> show access-list C. Router# show ip access-list D. Router> show interface ip access-list E. Route 1 P.O. box 198

2 Answers  


When using access lists, it is important where those access lists are placed. Which statement best describes access list placement? A. Put standard access lists as near the destination as possible. Put extended access lists as close to the source as possible. B. Put extended access lists as near the destination as possible. Put standard access lists as close to the source as possible. C. It isn't import where access lists are placed since the router will read and cache the whole list. D. Put access lists as close to corporate headquarters as possible.

1 Answers  






Identify the command that forces the router to load into ROM mode upon a reload? A.) boot system rom B.) rom boot C.) boot system flash rom D.) boot router rom

1 Answers  


Which command verifies encapsulation as well as Layer 1 and Layer 2 statistics on a router configured for Frame Relay? A. show ip B. show interface C. show statistics D. show frame-relay

1 Answers  


Which one is the Best protocol- Static routing, RIPV2,EIGRP,OSPF.

20 Answers   EIGRP, HP, Tech Mahindra, Wipro,


Do we subletting of ip?

0 Answers  


How do you disable CDP on the entire Router? A.) Router#no cdp run B.) Rotuer(config-if)# no cdp enable C.) Router(config)# no cdp enable D.) Router(config)# no cdp run

1 Answers  


What is Cisco's default encapsulation method on serial interfaces? A.) ANSI B.) Cisco C.) Q933a D.) HDLC

1 Answers  


What is GRE in PPTP?

0 Answers   CCIE,


Categories