Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...

CCNA Interview Questions
Questions Answers Views Company eMail

How IEEE Calculate the Cost of Link (ex.. 10mbps is having Cost 100) Is there any formula or any test to calculate it.

IBM,

2 3850

Which Circuit is mostly used by Clients in Frame-Relay PVC or SVC ?

TATA,

5 3641

I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

5 4664

Hi all of you, Actually this is interview qe? but i did,t do explain it completely so please give reply recently and completly Ans, what is sub-interface and inter-vlan ? And How to implement it on cisco router & switches and also which series router switches supported please write..........

Cisco,

2 4073

what is uplink port why are we use this port,this port having extra feature or only use to redundant link or other please explain it ,,,,,,,,,,,,,,,, bcz i am very confuse ..... Thanks

3 3537

any body can send me CCNA voice simulator practice exam software.

1 2660

hi shyam i am putting urs question here I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used

IBM,

1 2483

frends i am suffring from newfolder.exe virus in my server 2000 win how i have to remove it plz help me Jitendera sinha

5 3813

what is different between cisco router and layer 3 switch

Cisco, LABA Nepal,

8 12452

what is stub router

Satyam,

11 23200

I have one problem in my network my windows xp pc in workgroup there r 2 NIC card one I have disable in and second is active. The problem is in a day some time its ip conflict with other and when I see the event log and get the conflict ip mac and scan it with LAN scanner on one is there for that mac address nic in my network I have disable dhcp also don’t know what is the problem

8 5830

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 3071

Wnat do you know about zenpeck

2 3389

How convergence happen in ospf?

TCS,

3 4712

What hppends when ping 127.0.0.1 command executes?

CMS, Wipro,

10 28675


Post New CCNA Questions






Un-Answered Questions { CCNA }

In which ios version 182 people can access router through telenet?

153


Why ip address called logical address?

164


What’s the easiest way to remotely configure a router?

237


Which command we give on privilege mode for coming back to user execution mode?

153


Explain types of communication in ipv4?

160






What are the protocols that are used by every layer of ip/tcp model?

167


What is the difference between csma/cd and csma/ca?

163


what does the clock rate do?

202


What are the two types of transmission technology use in ccna?

141


What is the beaconing?

163


How many valid ip will b in /21 in route summarization?

134


I simulate ten routers r1 to r10 straightly. I want I can ping from the loop of r1 to loop of r10, but I want I cant ping r1 and r10 from inside routers.?

142


When we use loop back ip?

171


What is the difference between simple authentication and md5?

154


Does a bridge divides a network into smaller segments?

149