Interested to Buy Any Domain ? << Click Here >> for more details...
hi
i am facing one problem.ptoblem is like that i am getting
output error on mine router ethernet interfae
here is the cisco#show interface e0
Ethernet0 is up, line protocol is up
Hardware is QUICC Ethernet, address is 0030.802d.2a17
(bia 0030.802d.2a17)
Internet address is 202.122.20.225/28
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely
255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10
sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 05:55:07
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 10000 bits/sec, 11 packets/sec
5 minute output rate 29000 bits/sec, 11 packets/sec
1515202 packets input, 359100396 bytes, 1 no buffer
Received 6 broadcasts, 0 runts, 0 giants, 1 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored,
0 abort
0 input packets with dribble condition detected
1584394 packets output, 1623395338 bytes, 0 underruns
1820 output errors, 26732 collisions, 0 interface
resets
0 babbles, 0 late collision, 9698 deferred
18 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
output
cisco#
what is the reason
how to solve this
please tell me
i am using cisco asa 5520 behid mine internet router
and no error on the asa inside interface
- 2 Answers
- 5281 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / dharmendra kumar soni
Hi jit,
I think ........
1> Loop exits in the circuits friest you contact your leased
line provider.
2> Owner of remote router to remove loop.
Bcz your router creating loop. And your interface is
functioning properly.
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / jitendera
Hi d soni
There is no any loop in mine network.look what ia have done
for this
i removed the patch cable comming from asa firewall to
switch and i take the new one working patch cable and
coonect it to the mine laptop (this one is also barnd
new.ha ha)
now the senarion become like that
internet router
\
\
asa firewall
\
\
\
laptop
as of now i am the single user connectd to the internet
there is no any loop in mine network and i am stiil getiing
drop?
now what i am thinking
scince we are using 1600 cisco router as internet router
which have the e0 port and mine asa have the fa0/0 port
so it might be possible that there is interface micmatch
but only 1% chance but let me try this one i am going to
palse higher end router verry soon
if this problem is solved then all right nithere i will
look towrads u people
thanks
| Is This Answer Correct ? | 0 Yes | 0 No |
Which of the following is a valid extended IP access-list? A.) router(config)# access-list 101 permit tcp host 172.16.30.0 any eq 21 log B.) router# access-list 101 permit tcp host 172.16.30.0 any eq 21 log C.) router(config)# access-list 101 permit any any 172.16.30.0 D.) router(config)# access-list 101 permit ip host 172.16.30.0 any eq 21 log
Which of the following is not a characteristic of link-state routing protocols? ❍ A. VLSM support ❍ B. Route summarization at any bit level ❍ C. Full routing updates at regular intervals ❍ D. Discontiguous network support
what is the difference between 1 router and switch 2 router and hub 3 hub and switch 4 bridge and switch
What is a function of a reliable transport layer connection? A. route selection B. acknowledgements C. session checkpoints D. system authentication
Identify the command to configure DLCI 100 on an interface e0? A.) Router(config)# frame-relay local-dlci 100 B.) Router(config)# frame-relay local-dlci 100 int e0 C.) Router(config-if)# frame-relay local-dlci 100 D.) Router(config-if)# frame-relay local-dlci 100 int e0
How many Frame-relay encapsulation types are available with Cisco routers? A.) Four B.) Two C.) Five D.) Three
Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0
What is the formula for metric of ospf?
Which of the following are Transport layer protocols? A.) UDP B.) TCP C.) NBP D.) IP E.) SPX
Explain protocol?
how will configure Nat
How many fillers we can put in one ip of ipv6?
CCNA 
