hi shyam i am putting urs question here
I am facing one problem in my layer 2 switch I don’t know
the problem is on switch side or client side. The problem is
some PC (not all) are stop participate in LAN they don’t
send or recd. Packet from switch and if I check RJ45 (with
LAN tester)from PC side the packet and 8 pin wire is working
fine and after that process of LAN tester I plug RJ 45 in PC
now PC start recd/ send packets what is the problem I don’t
understand even client side no virus found RJ45 is ok and
switch has no problem bcoz other PC is working fine Cable
(cat 5 ) is also fine bcoz I didn’t crimp again just check
in LAN tester and start working fine. Plz any one solve this
matter. And after lan tester process pc is working fine and
after 2 or 3 hour it again start same problem and again same
process lan tester I have used
- 1 Answers
- 4072 Views
- IBM, I also Faced
- E-Mail Answers
Answer / jitendra
OK as now u told that you are not sure that stp is working
on l2 or not
stp is working on any switch either it is l2 or l3.
i think stp is not problem for urs problem problem is some
where else.
can you do one thing can you connect different com. or lap
or on particular switch switch port for 2 to 3hree hrs.
if the problem arises then problem with switch and if not
come then you have to scan the system with good antivirus.
2nd thing can you check that particular switch port is in
full duplex or half duplex mode?.
if it is half duplex make it full or auto.
do the first one first i think it will solve your prob.
can you send the screen shot(other than cisco)/conf file (if
cico) of your switch on my gmail accounts
jitenderasinha.it@gmail.com
but do the first one first it should solve urs issue
| Is This Answer Correct ? | 4 Yes | 1 No |
What does a router change in a packet when it forwards a packet to the next hop? * A: Destination physical address * B: Destination network address * C: Destination network address and the destination physical address
How does the cut-through switching technique work? A.) By using broadcast address as source addresses B.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets C.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface D.) By using a Class I repeater in a collision domain
As the system administrator, you type "ppp authentication chap pap secret". Which authentication method is used first in setting up a session? A. secret B. PAP C. CHAP D. PPP/SLIP
what is 5-4-3 rule?
What does the following line for an access list do? 'access-list 101 deny tcp 3.4.5.0 0.0.0.255 any eq 23' A.) deny all ftp traffic B.) deny all ftp traffic from subnet 3.4.5.0 C.) deny all telnet traffic from subnet 3.4.5.0 D.) deny all ftp traffic to subnet 3.4.5.0 E.) deny all telnet traffic
Explain how many types of ends in wan?
Which of the following describe SMTP? A.) Used for downloading files to the router. B.) Used for sending e-mail. C.) Uses TCP. D.) Uses UDP. E.) Uses port 25. F.) Used for managing IP devices.
Which three basic switch functions increase available bandwidth on the networks? (Choose three) A. loop avoidance B. address learning C. hop count limiting D. broadcast filtering E. packet forward/filtering
What is matric?
Identify 3 characteristics of the Network layer (OSI layer 3)? A.) Connnection oriented B.) Path determination C.) Supports multiplexing D.) Manages sessions E.) Packet forwarding
what is stub router
What is public and private ip address., explain? and also explain the ip address range of both public and private? and where we use that public and private ip address?
CCNA 
