Answer / bejoy

in 2 stroke engines too valves can be designed and also
there are 2 stroke diesel engines with valves..
but common 2 stroke engines like that of a kinetic honda
engine don't have valves bcos it simplifies the construction
a lot and by arranging the ports in such a manner it
achieves the purpose..bt then it creates a lot of
inefficiency and waste of lubricant.. so no valves are used
where these can be compromised or minimised by other methods..

Answer / yash chauhan

basically ports and valves are same, they are used interchangeably most of the times but the basic difference in between them is Ports are mainly the opening in the cylinder head they allows the passage of gas/mixture to the cylinder whereas Valve are moving up and down allowing the gases to come or to escape from engine cylinder.

Answer / atul sharma

In two storke engine two storke will take palce
simultaneously so no need to uses valve .But in case of
four stoke engine all the operations are takes place
different time so valves are required .

Answer / babu

in two stroke engine needs suction and charging at the same
time when the piston move down wards air fuel mixtures
enters throgh port due to the hitting of back portion of the
piston ..

function of the strainer in ic engine?

3 Answers   Castrol,

---

2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand

0 Answers  

---

A BEARING IS DESINED AS 6205. WHAT IS IT"S BORE DIAMETER?

4 Answers  

---

Who has the most influence in ur life? & in which way?

0 Answers   RC, TCS,

---

What is allotrope ? In what forms of cubic pattern, iron exists ?

0 Answers  

---

difference between strengh and toughness.

5 Answers   Unitech,

---

After any cause of repaired how i start the engine by slow speed 800 to 900 rpm electronic control moudle engine [cummins]

0 Answers   Cummins,

---

Is it able to make FMEA for Pencil creation? If yes send the FMEA

0 Answers  

---

Which one is more efficient? A four stroke engine or a two stroke and why?

20 Answers   Maruti Suzuki,

---

difference between aerofoil meter and orifice meter 

0 Answers   Cethar Energy,

---

What between defrance of vertical deegry and horigental deegry.

0 Answers  

---

What do you mean by KG and KGS in Diesel Engine

0 Answers   Akij, BEL, Cipla, HCL, Honda,

---