Interested to Buy Any Domain ? << Click Here >> for more details...
what is the function of switch gear ?
- 10 Answers
- 30208 Views
- Exxaro, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / rahul
switchgear is nothing but indoor version of switchyard.
its main function is switching operations in electrical
ckts.they r used to de-energize equipment to allow work to
be done and also to clear faults downstream.
| Is This Answer Correct ? | 52 Yes | 7 No |
Answer / chelladurai.p
The basic function of switch gear is to control the supply
of Electric power and protect the equipment in the event of
abormal condition
| Is This Answer Correct ? | 33 Yes | 3 No |
Answer / harmeet singh
switchgear
main function is switching operations in electrical
ckts.they r used to de-energize equipment to allow work to
be done and also to clear faults downstream.
| Is This Answer Correct ? | 7 Yes | 0 No |
Answer / pravin s choubey
The function of switch-gear is protection and interrupt short-circuit and faulty current and maintain service of unaffected current and give isolation in supply from circuit
| Is This Answer Correct ? | 7 Yes | 0 No |
Answer / mxolisi
The above answer is correct, but I want to know if a
switchgear can be thought of as one device or a combination
of devices?
| Is This Answer Correct ? | 10 Yes | 6 No |
Answer / shaji samuel
I mean about the switch gears is the breaker mediater of
circuite flows to two points.
| Is This Answer Correct ? | 10 Yes | 6 No |
Answer / sunil guru
in switch gear not all provisions but few are provided as a switch yard like.....
switching ,protections and power factor improvement with circuit breakers,relays,mccb's, contactors,capacitors and fuse units
as switch gear system is panel based system so has some limitations and other than that mainly used for meter displays purpose like V,I,p.f,kwh,frequency etc....
for any disagreement pl contact me on parmar20072008@yahoo.com
| Is This Answer Correct ? | 9 Yes | 6 No |
Answer / banda saivarun
switch gair is used for switching operation like if any faults occurs the related equipment may damage to avoid that here we are using switching components like MCCB,FUSES,CIRCUITBREKERS,RCCB etc so with out switching devices there is no electrical system
| Is This Answer Correct ? | 3 Yes | 0 No |
Answer / swathi
swithgear is a device by which we can reduce the fault
occurences in our equipment.
| Is This Answer Correct ? | 6 Yes | 4 No |
Answer / sreelal
switch gear is a combination of electrical disconnected switches and breakers used to isolate equipments in substations
| Is This Answer Correct ? | 4 Yes | 3 No |
H.t motor 6600 volt to same motor lt supply 440volt supply applyed to h.t motor to effect....
Name a govt approved university which have 100% online engineering course.
WHAT IS THESETTING CALCULATION FOR THE RELAY?
Where we use 30mA , 100mA & 300mA RCCB ?
how to design domestic earthing pit and earthing wiring?
What is the difference between 11kv/110v & 33kv/110v ? If both 11 & 33KV give 110v then what is the diiference ?
In ht capacitor ckt we are using LBS Panel it having isolator with fuse, one of HT fuse flash over, so what is reason behind this event.
Why we use RYB phase sequence?
Why do we choose 33kV transmission for industrial purpose and 11Kv for township?
why the rating of transformer in k.v.a
What is the scale analysis for condensor of HVAC system
How much depth n width required for laying of 1X70 Sqmm Cable in Desert???
0 Answers Alka Electromech, Aramco,
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
