what happens if DG N earthing fails while running and N
Earthing fails while Transformer on load ???what will be the
impact ???????/

Answers were Sorted based on User's Feedback



what happens if DG N earthing fails while running and N Earthing fails while Transformer on load ?..

Answer / pillay

sorry about the earlier answer.
if the DG or xformers load was balanced when the neutral
failed than there would had been no impact, B cause the
summation current is zero but if it was loaded with a
unbalanced load than the phase voltage would be unbalanced
and cause damage to single phase equipment. the single phase
voltage can raise up to phase to phase voltage depending on
the load current.

Is This Answer Correct ?    4 Yes 0 No

what happens if DG N earthing fails while running and N Earthing fails while Transformer on load ?..

Answer / pillay

In both cases if the Neutral connection from the DG set or
from the Transformer to the load is not interrupted than there
is no impact at all.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

what is softstarter? explain briefly where it is used?

2 Answers   Essar,


Why the capcitor to be discharged after put in to operation & why not inductor though the both elements stores energy?

3 Answers  


In India which type of PLCC IS used?

2 Answers   Cipla, Ford, Jayashree,


first 3 men were there .again 3 came.total how much?

11 Answers   Wipro,


if i conncet ct with ct ratio of 600/5 to an energy meter having ct ratio of 100/5, the reading show by the meter will correct, if wrong is there any method to calculate correct value with shown value, if yes please state it.....

2 Answers  






can you give me some names of projects which can be used in our daily life & which is having medium cost?

1 Answers  


How to calculate the fuel consumption for 600kva DG genset which connecting with 25%load?

0 Answers   Debbas, GE, TCS,


What is the Surge for 1.1 Phase Induction Motor(For Eg.1Hp) 2.3 Phase Induction Motor(For Eg.1Hp) 3.AirConditioner(For Eg 1Ton) 4.Refrigerator(For Eg 180Ltr or 160kW) 5.Induction Cooker 4. Ceiling Fan

0 Answers  


Bus-bar is made of which material & name of mostly used material in bas-bar design ?

7 Answers  


iam completed my DEEE in eillm university. can i get the c licence in tamilnadu its possible or not

1 Answers  


WHY SPEAKER OUTPUT IN WATTS??

2 Answers  


Why more than 2.5 MVA distribution transformers (secondary is 440V)are not used in india.

1 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)