Answer / keshav

you can download them from
http://examrace.com/IFSpreviousyrpapers.aspx

CHEMICAL ENERGY BALANCE - EXAMPLE 11.5 : According to Margules Equation, P = x(1) p(1) g(1) + x(2) p(2) g(2) for a two-component mixture where P is bubble pressure, x is mole fraction, p is saturation pressure, g is constant given by ln g(1) = x(2) A x(2). Find the value of A as a constant when P = 1.08 bar, p(1) = 0.82 bar, p(2) = 1.93 bar in a 50 : 50 mole fraction mixture. Estimate the pressure required to completely liquefy the 30 : 70 mixture using the same equation, by proving P = 1.39 bar. Take note that ln g(2) = x(1) A x(1), ln g(1) = x(2) A x(2).

1 Answers  

---

what is meaning of pid how it is useing controlers

4 Answers  

---

any meter avilable for measureing the Transformer Losses. ( like Voltmeter for voltage & ammiter for currenr )if yes plz give the make & supplier address, Email, Phone number.

0 Answers   Piramal Healthcare,

---

Explain the some guidelines for sizing a psv for a fire scenario on a vessel in a refinery service?

0 Answers  

---

For a heat exchanger, will the overall heat transfer coefficient increase along with an increase in lmtd (log mean temperature difference) around the unit?

0 Answers  

---

---

what is a pschycometric chart and how to use it?

1 Answers  

---

Why is post-weld heat treatment (stress relieving) sometimes necessary for welded vessels?

0 Answers  

---

Any idea on recombinant protein expression?

0 Answers  

---

HEAT TRANSFER - EXAMPLE 5.3 : In a cylinder with a hollow, let a is outside radius and b is the inside radius. In a steady state temperature distribution with no heat generation, the differential equation is (d / dr) (r dT / dr) = 0 where r is for radius and T is for temperature. (a) Integrate the heat equation above into T(r) in term of r. (b) At r = a, T = c; at r = b, T = d. Find the heat equation of T(r) in term of r, a, b, c, d.

1 Answers  

---

What is the average salary for chemical engineers?

0 Answers  

---

Question 75 - The molecular weights M in kg / mol of 3 different monomers a, b and c in a polymer are Ma = 14, Mb = 16 and Mc = 18. The fraction of polymer chain X of 3 different monomers a, b and c in a polymer are Xa = 0.5, Xb = 0.3 and Xc = 0.2. (i) Calculate number average molecular weight by using the formula Ma Xa + Mb Xb + Mc Xc. (ii) Calculate weight average molecular weight by using the formula (Ma Xa Ma + Mb Xb Mb + Mc Xc Mc) / (Ma Xa + Mb Xb + Mc Xc). (iii) Calculate the polydispersity by using the answer in (ii) divided by answer in (i). (iv) If the molecular weight of repeat unit is 12, calculate the degree of polymerization by using the formula (Ma Xa + Mb Xb + Mc Xc) / (molecular weight of repeat unit).

1 Answers  

---

BIOCHEMICAL ENGINEERING INSTRUMENTATION - EXAMPLE 29.3 : In thin layer chromatography (TLC), let retention factor Rf = (distance traveled by solute) / (distance traveled by solvent). Silica gel is used as stationary phase which is more polar than the hexane solvent as mobile phase. If the Rf values of 3 solutes A, B and C are 1.5, 0.75 and 1 respectively, compare the polarities of A, B and C with reasons.

1 Answers  

---