What are the advantages of star-delta starter with
induction motor?
Answers were Sorted based on User's Feedback
Answer / k.senthil kumar
1. The main advantage of using the star delta starter is
reduction of current during the starting of the
motor.Starting current is reduced to 3-4 times Of current
of Direcr online starting.
2. Hence the starting current is reduced , the voltage
drops during the starting of motor in systems are reduced.
Is This Answer Correct ? | 132 Yes | 15 No |
Answer / sonu kumar
The main advantage of using the star delta starter is
reduction of current during the starting of the
motor.Starting current is reduced to 3-4 times Of current
of Direcr online starting.
Hence the starting current is reduced , the
voltage
drops during the starting of motor in systems are reduced
Is This Answer Correct ? | 53 Yes | 15 No |
Answer / amrinder singh rajomajra
The main adventage of using star-delta starter for
induction motors is as following-
if we start the motor with DOL(direct on line) or simple
starter the the motor requiers more current to start ,
which is 6-8 times the full load current.because the higher
tourqe is require to start the motor...
so in star-delta the motor is started in star, which
produce higher tourqe at lower current, means the starting
current is 4-5 times less than delta starting.
and then motor after start gets full speed and star
contecter is disconnect and motor runs in delta
connections.because torqe is less and lower current is
required.
Is This Answer Correct ? | 34 Yes | 6 No |
Answer / mohanraj
1. The main advantage of using the star delta starter is
reduction of current during the starting of the
motor.Starting current is reduced to 3-4 times Of current
of Direcr online starting.
2. Hence the starting current is reduced , the voltage
drops during the starting of motor in systems are reduced.
Is This Answer Correct ? | 23 Yes | 5 No |
Answer / partha
How the current is being reduced to 1/3 times in star/delta
starting. Can you please show it by derivation.
In my views power is reduced by 1/3 times and current and
voltage by 1/root 3 times. pls correct.
Is This Answer Correct ? | 14 Yes | 6 No |
Answer / jishnu mukherjee
The main advantage is of-course the issue of starting current.In this case the starting line current is reduced to one third.Most importantly, starting torque is also reduced by the same amount.So pumps,motor-generator sets, where starting torque is not required to be high can take the advantage of star-delta starting.
But the problem is, this method is not adoptable for the motors which have high voltage rating(generally above 3kv).The reason behind:such motors are usually star-connected.We must have delta connection in the induction motor.
Is This Answer Correct ? | 7 Yes | 3 No |
What are insulation classes? Tell examples of each of them.
How much load can give on 1600 kva transformer 11kv/440
why in india the voltage generate multiply by 11,,,like 220v,440v,11kv,33kv,66kv,220kv,
3 Answers NTPC, Servotech, Tata Power,
why we are grounding the neutral?
How can we calculate the fault level of the distribution system knowing the percentage impedance of transformer & subsequent equipments.
which transmission is cheaper ac or dc?
A 230V, 60W bulb when connected to 230v supply what current and power will consume, if same bulb is connected to 200v what purrent and power will consume?
What OPGW is better than Microwave or PLCC???
low voltage distribution is done by a)3 phase 3 wire b)3 phase 4 wire c)single phase
what is static excitation and dynamic excitation of synchronous generator,scr excitation is a brush or brushless excitation?
what are the functions & ratings of panels mentioned below: 1. Main LT Panel(MLTP) 2. Motor Control Centre(MCC) 3.Feeder pillars 4.Busducts
Explain the experiment on ward leonard method of a speed control on a dc shunt motor with an suitable circuit diagram.