Interested to Buy Any Domain ? << Click Here >> for more details...
what is the means of stress
- 8 Answers
- 9737 Views
- Claris Lifesciences, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / kumar
as per formulae,
stress(newton/sq.m) = load/unit area
| Is This Answer Correct ? | 9 Yes | 2 No |
Answer / hari prasad
Stress is the internal resistance, or counterfource, of a
material to the distorting effects of an
external force or load. These counterforces tend to return
the atoms to their normal positions.
The total resistance developed is equal to the external
load. This resistance is known as stress.
| Is This Answer Correct ? | 9 Yes | 2 No |
Answer / ram krishan singh
the resistance offered by the body per unit area aginst
failure is knon as stress
| Is This Answer Correct ? | 5 Yes | 2 No |
Answer / kalesh
Whenever an external force is acting on a body, an internal
resistance is setup in that body. This internal resisitance
offered by the body per unit area is called stess.
Stress = load/unit area.
The unit is N/mm2 (S.I.Unit)
Types : 1.Tensile stess
2.Compressive stress
3.Shear stress
4.Bending stress
| Is This Answer Correct ? | 3 Yes | 0 No |
Answer / karthick
stress is the internal force devloped inside a body due to
the application of external force
| Is This Answer Correct ? | 4 Yes | 2 No |
Answer / vikas
the load applied per unit area on a body is "stress".
stress(newton/sq.m) = load/unit area
| Is This Answer Correct ? | 2 Yes | 1 No |
Answer / m. sohail iqbal
When an external force acts upon a body, an internal
resistance is setup in that body. This internal resistance
offered by the body per unit area is called stress.
Stress = load/unit area.
The unit is N/mm2 (S.I.Unit)
Types : 1.Tensile stress
2.Compressive stress
3.Shear stress
4.Bending stress
| Is This Answer Correct ? | 1 Yes | 1 No |
it is internal resisting force per unit area of body
| Is This Answer Correct ? | 0 Yes | 1 No |
what is the required force to bend 2.5 MS sheet in 90 degrees and what is the formula to calculate the same?
What is meant by free or natural convection?
Why combustion chamber is used in gas power plant cycle? What will happen if compressor output is directly provided to gas turbine?
On what basis can sliding contact bearings be classified? Explain?
in boiler light up y APH start first
Why Air Conditioner capacity measured in Ton. Like 1.5ton
• Tell me more about your experiences in this qualification and since when you have been working on this profession till date?
The capacity of the compressor is considered to be maximum when the temperature of the air is a.Maximum b.minimum c.moderate d.
what is ultrasonic flaw decdector?
draw IRON-CARBON diagram.
What is L 110 spider? What does L &110 indicate
1 Answers Emmennar Pharma, Mega Limited,
The Length of the Divergent Cone is about 3 to 4 times than that of the Convergent Cone why
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
