Input power is 380 - 450 V but with 45 - 55 Hz frequency -
desired output is 415 V and 50hz with 1% variation
permissible. CVT / Servo dont stabilize the Frequency -
what is best solution??

Answers were Sorted based on User's Feedback



Input power is 380 - 450 V but with 45 - 55 Hz frequency - desired output is 415 V and 50hz with 1..

Answer / rvg

SMPS- switch mode power supply is the best solution for
such frequency variable supplies.

Is This Answer Correct ?    7 Yes 0 No

Input power is 380 - 450 V but with 45 - 55 Hz frequency - desired output is 415 V and 50hz with 1..

Answer / yuvi

I completely agree with Rvg. SMPS is the best possible
solution when it comes to varying the frequency and
voltage. Good thinking Rvg. Compact, efficient and
effective, the only disadvantage is radio noise created by
it which can be easily shielded.

Is This Answer Correct ?    0 Yes 0 No

Input power is 380 - 450 V but with 45 - 55 Hz frequency - desired output is 415 V and 50hz with 1..

Answer / vinay

using PIU(POWER INTER FACE UNIT).its working is i/p voltage
is HIGH r LOW.but o/p is CONSTANT.

Is This Answer Correct ?    0 Yes 0 No

Input power is 380 - 450 V but with 45 - 55 Hz frequency - desired output is 415 V and 50hz with 1..

Answer / k.prakashchandra

Frequency is dependent on the prime mover, the speed
regulation of which, is very bad.

Is This Answer Correct ?    0 Yes 0 No

Input power is 380 - 450 V but with 45 - 55 Hz frequency - desired output is 415 V and 50hz with 1..

Answer / vikramsenareddy

please arrange AVR( autometic voltage regulator)

Is This Answer Correct ?    1 Yes 2 No

Input power is 380 - 450 V but with 45 - 55 Hz frequency - desired output is 415 V and 50hz with 1..

Answer / shilpa

the logic behind stabilising the frequency fluctuations is
to slow down the rate of change of current in the circiut.
we should use a proper rating inductor in serieswith the
supply....thats it.

Is This Answer Correct ?    1 Yes 2 No

Input power is 380 - 450 V but with 45 - 55 Hz frequency - desired output is 415 V and 50hz with 1..

Answer / mubashar ali

Question is not clear , bcz i dont know about source of
power, if generator then u should be istalled AVR, not
possible this fault in grid supply

Is This Answer Correct ?    1 Yes 3 No

Post New Answer

More Electrical Engineering Interview Questions

IN SINGLE PH TRANSFORMER IF LEKAGE IMPEDANCE DROP IS NEGLECTED ,THE FLUX IN THE MAGNETIC CORE and the lekage flux linking a winding are a)proportional to the applied v to the winding i respectively.

0 Answers  


how solar power plant energy meter multiplication factor

0 Answers  


What are the main parts of central chiller plant? Explain the function of each stage.

0 Answers   HSL, Shankar Electricals,


how capacitor can split the phase.

1 Answers  


why using carbun bresh in dc motor

3 Answers  






ELCBs are installed for protecting humans from AC leakage current.Is there a device which protects humans from DC Leakage current??e.g.leakage from batteries...If not,then why so???

1 Answers  


Do closed loops systems require manual input?

0 Answers   Ericsson,


what is the meaning of vcc

0 Answers  


How can Inductive load reduce the line voltage of HV transmission line and vice versa Capacitive load?

1 Answers  


what is the current density of copper & alluminium.

0 Answers  


WHY CAN WE NOT CHAGE SPEED OF SYNCHRONOUS MOTOR...............................JUSTIFY

2 Answers   ISMT,


Hy the hydro power stations have high transmission and Distribution costs?

3 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)