Answer / asutosh

for a perticular design the incoming power is same.
we know P = VI so when voltage is high current is low &
viceversa.

Answer / jital

Voltage & Current are the inverse propotion ( Voltage is
High, Current is less & Voltage is low, Current is More )
for the Same load when considered on different voltages.
its following P = VI

I.E> For the Same Load in 11 KV Current will be very less

For the same load in 415 V Current will be high compare to
11 Kv

Answer / bapi

AS kVA RATING OF A TRAFO IS CONSTANT.
SO FOR HT SIDE MEANS HIGH VOLTAGE SIDE CURRENT IS LESS &
FOR LT SIDE MEANS LOW VOLTAGE SIDE CURRENT IS MORE.
HIGH VOLTAGE X LOW CURRENT = LOW VOLTAGE X HIGH CURRENT
(HT SIDE) (LT SIDE)

Answer / bhavesh chauhan

Voltage and Current are inversely proportional to each other in Transformers.. As the value of voltage increases current decreases, and as the value of voltage decreases the current value increases.... I Will make you count..
Practically i work in a 220/66/11 kv power station.
I have a 100 MVA Transformer which is a Step Down X'mer. The H.V Side of the X'mer gets 220KV input and L.V of the X'mer gives 66KV output...Now to calculate ............
The Current for H.V Side according to P=VI
we have P=100 MVA
V=220 KV
I=?
I= 100 10^6 /1.732 X 220 X 10^3 = 262.24 Amps

Similarly for L.V
I= 100 10^6 /1.732 X 66 X 10^3 = 874.79 Amps

These are the Actual H.V and L.V Current reading of a working transformer... Which proves that when Voltage decreases current increases..........Thank you

Answer / subu

in ht side no of turns is high as compered to Lt side, so
voltage is high and current is low where no of trns is
high. voltage is low and current is high where no of turns
is low

HOW CIRCUIT BREAKER RATING CALCULATED?WHAT ARE THE PARAMETERS CONSIDERED?

5 Answers  

What is the equivalent circuit of a transformer and its vector diagram?

0 Answers   Bhel, Madhucon,

Define damping ratio.

0 Answers  

how many single tension hardware are required on a double circuit transmission tower?

0 Answers  

What is sinusodial & non sinsodial current

1 Answers  

Name the test signals used in control system

0 Answers  

Write the difference between OCB,VCB ?

3 Answers   Svam Power,

i am an maintenance engineer. one distribution board have 5 feeder. recently its ELR trips frequently, but it take some times after trip( 10min,20min..)but 3 feeder no load. two feeder only loaded. i checked one feeder IR value all values are above 50Mohm.but B phase to Earth is only 9Mohm.any problem about low value

0 Answers  

When we use air circuit breaker, it has O/L protection ,time delay SC protection, Instataneous SC protection & ground fault protection. They all have some setting range. But what is the suitable/allowable setting for the above protection which will be safe for the equipment? For example-O/L protection setting have a range of (0.4,0.45,0.5,0.55,0.6,0.65,0.7,0.8,0.9,1.0)xIn Time delay SC protection have a range of (1.25,1.5,2,3,4,6,8,10,12)xIn Time delay setting is 0.02,0.1,0.2,0.3,0.4 Instataneous setting is fixed to 20xIn Gound fault setting is given 100A,300A,600A,900A,1200A This setting are for 2500A ACB. So what will be the basic allowable setting for the above protection? is there any formulae to calculate this<

0 Answers   Lupin,

What is the fullform of NS fuse

2 Answers   Google, JAL International,

WHTA IS LIMT OF LEAKGE CURRENT OF 11 KV 1 CORE 1000SQ.MM. XLPE CABLE.LOAD ON CABLE IS AROUND 600AMP .LENGTH 500 MTRS.

0 Answers   L&T,

what are the causes for strip heater failure ?

1 Answers