Answer / gaurav kale

you can use 0.5 Sq mm shieled for analog .....Upto 600 m no
problem ....but generally as per standerds above 500m you
will have to go with Fibre optic cable

Answer / laxit

For this type of circuit, use Relay output instead of
direct driving through the PLC output. As these SOV's are
not the low power wattage, Prefer to use 2.5 Sq.mm as a
general for such digital output.Relay contact shall be
selected accordingly.

Answer / jayeshpateler

as per the 1cm3 core wire will be find also check the
current require then as per the current if it is higher
than you can carry but if current is low then you need to
use the repeater for that.

Answer / mwah

yes gaurav kale is right about 0.5 sq.mm twisted pair
shielded cable but u have to install repeater to make sure
theres no degrading of the signal at the end.

Answer / janes

It is all depends on the Load of the Field Instrument.
After Getting the load apply the Voltahe Drop Formula.
Also the input is 24VDC but define the Amp. is it 20A/ 10A.
that is 24Vdc 10A.

For 24VDC 10A Power supply and the Field Instrument is SOV
with 18 Watts, and the Distance is 600 meter then use the 2
Core 2.5 Sqmm Cable as per below Formula.

% Voltage Drop = Length X Current X R Cos0 + X sign0 /
Number of run X Voltage X 10.

what is the difference between E/P positioner and I/P positioner in control valve , in which application the respective positioner are used in.

1 Answers   ABB,

what effects a surging can produce in the compressor

0 Answers   Nemat,

draw a loop drawing of vibration beginning to end

1 Answers  

WHAT IS MEANT BY SUPERVISORY CONTROL?

3 Answers  

in a power plant which system are compensated?

2 Answers  

in sports(eg,cricket) what is the technique for measurement of speed of the ball thrown by the bowler.

6 Answers   BEL, PSU,

what does a positioner in control valve ?

11 Answers  

ALL INSTRUMENTS WORKING PRINCIPLE.

3 Answers   Blanco, India Cements, TVS,

my data card only does run in my mobile so how can change it that it run other mobile & computer and i can stor data in my data card

0 Answers  

What is the difference between a PLC (Programmable logic controller) and DCS (distributed control system)?

7 Answers  

a laways iface problem with brine level transmitter sealing diaphram a laways giving error and maximum reading i made re range and adjust with side glass but during commission it giving gap reading between it and side glass i need help from expert to explain how to calibrate it. note:dp transmitter yokogawa company

1 Answers  

A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.

0 Answers   MNC,