What is the meaning of the critical speed of a turbine, and what are its effects on the shaft line
Answer / surya kirna
the critical speed of a turbine is the spped at which the axial and radial vibrations of the turbine are matched with the axial and radial vibrations of the shaft of the turbine(even the total turbine). because of that the these two are in resonace with each other and causes the breakdown of the mechine.
Is This Answer Correct ? | 1 Yes | 0 No |
how much maximum power can be generated by 320v, 10kg-cm synchronus motor if shaft is roteted mechanically at 50 to 60 rpm?
MASS TRANSFER - EXAMPLE 4.1 : A concentric, counter-current heat exchanger is used to cool lubricating oil. Water is used as the coolant. The mass flow rate of oil into the heat exchanger is 0.1 kg / s = FO. For oil, the inlet temperature TIO = 100 degree Celsius and the outlet temperature TOO = 55 degree Celsius. For water, the inlet temperature TIW = 35 degree Celsius and the outlet temperature TOW = 42 degree Celsius. What is the mass flow rate of water in kg / s, FW needed to maintain these operating conditions? Constant for heat capacity of oil is CO = 2131 J /(kg K) and for water is CW = 4178 J /(kg K). Use the equation (FO)(CO)(TIO ?TOO) = (FW)(CW)(TOW ?TIW).
Mention some of the specialized crushing methods?
ENGINEERING MECHANIC - EXAMPLE 15.3 : A biochemical trolley of mass 15 kg is towing a trailer of mass 5 kg along a straight horizontal pathway. The trailer and the trolley are connected by a light inextensible tow-bar. The engine of the trolley exerts a driving force of magnitude 100 N. The trailer and the trolley experience resistances of magnitude 10 N and 30 N respectively. (a) Form 2 equations with unknowns T and a, that represents the equilibrium for the 2 systems of the trolley and trailer. (b) Solve the simultaneous equations from the 2 equations that are obtained in part (a) of this question. T is the tension of the tow-bar and a is the acceleration.
What are the different ways in which solids can be blended?
Chemical Engineering Unit Operation - Which of the sequence below represent a feasible flows of ethanol processing plants using cellulose as starting material? A. raw material --> heat exchanger --> distillation column --> reactor. B. reactor --> distillation column --> raw material --> heat exchanger. C. heat exchanger --> raw material --> distillation column --> reactor. D. raw material --> heat exchanger --> reactor --> distillation column. E. distillation column --> raw material --> reactor --> heat exchanger.
BIOPROCESS ENGINEERING - EXAMPLE 14.2 : An aqueous solution with 2.5 g of a protein dissolved in 600 cubic centimeters of a solution at 20 degree Celsius was placed in a container that has a water-permeable membrane. Water permeated through the membrane until the h - level of the solution was 0.9 cm above the pure water. (a) Calculate the absolute temperature of the solution, T in Kelvin, where T (Kelvin) = T (degree Celsius) + 273.15. (b) Calculate the osmotic pressure, P of the solution by using the formula P = hrg where h is level of the solution, r is density of water with 1000 kg per cubic meter, g = 9.81 N / kg as gravitational acceleration. (c) Calculate the concentration of the protein solution, C in kg / cubic meter. (d) Calculate the molecular weight of the protein, (MW) = CRT / P where R = 8.314 Pa cubic meter / (mol K) as ideal gas constant.
Explain the Deacon reaction?
How many grams per liter would there be in a 0.35 n (normality) citric acid solution?
what is the melting point of ash?what is value of ash in crude oil?
ACCOUNTING AND FINANCIAL ENGINEERING - EXAMPLE 34.4 : A university is enrolling new students of biochemical engineering degree. A long queue is formed during registration. Let L = rate of newcomers to a queue, m = number of clients served at a certain time, T = time in system. In M / M / 1 queue, let T = time waiting in a queue + service time, L = 2 / second, m = 3 / second. (a) Find the service time, A = 1 / m. (b) Calculate time waiting in a queue, B = A (L / m) / (1 - L / m). (c) What is the value of T?
Explain what are the methods involved to test helium leak testing in a vacuum system?