What is the right procedure for adjusting the gap voltage
of bently nevada vibration sensor?

Answers were Sorted based on User's Feedback



What is the right procedure for adjusting the gap voltage of bently nevada vibration sensor?..

Answer / imran mansuri

for vibration sensor installation take digital multimeter
connect on proxymeter out signal + comma (-) now insert
first your proxyprobeon sahft untill it's not touch body
you will get 0 volt output now unscrew proxy untill you
get -9.0vdc or -10 vdc equal 50 mil this is procedure that
i know

Is This Answer Correct ?    14 Yes 2 No

What is the right procedure for adjusting the gap voltage of bently nevada vibration sensor?..

Answer / rana mujahid

first check all the physical checks like,prob material is
correct for service,cable length is proper accroding to
proximeter,termination,supply is proper(-24vdc),etc..
after this connect volt meter with proximeter b/w out and com.
and try to adjust exact -10vdc but -9.5 to -10.5 are ok just
configured in systm.

Is This Answer Correct ?    7 Yes 0 No

Post New Answer

More Instrumentation Interview Questions

What is mean by ATEX?

1 Answers  


what is The specifications for oriface instalation

0 Answers  


what is the difference about HART, and 4-20mA signal?

8 Answers  


can we control operation of PLC from operator station?

3 Answers  


hye SAM acn u send your e mail id, so that i can solve my query through e mail?

0 Answers  






steps for installing orifice plate?

0 Answers   Bhushan Power Steel,


What is standard of DCS panel design?and what is step of DCS panel design?wiring and type of connector(screw or DB connector)

0 Answers  


Shall we get the reading on level transmitter only by termination,without commissioning?

1 Answers  


how many mmwc are eual to 1kg/sq.cm & can we calculate mmwc into tph?

2 Answers  


Furnace draft transmitter range is -50 to +50 mmwc. why the impulse line connected in hp side?

2 Answers   Arena,


Q- Control problem are mainly classified in _____ types. a-)4 b-)3 c-)6 d-)nono of these Few of them i know is 1- regulator type problem (eg- Air conditioner) 2- tracking problem (eg missile trcking problem) 3- sybernatics 4- optimal control problem

0 Answers   Sail,


1.In which princeple DP transmeter works? 2.Why UPS system is use for DCS? 3.How drum lvel controller works? 4.What is the difference between glob valve and gate valve? 5.How axial shift probe work & in which princeple it works?

1 Answers   Luberef, Qatar Gas, Reliance,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)