I BOUGHT A HAVELLS ACCL WITH GENERATOR STOP FASCILITY(i.e- BASICALLY IT IS A A

I BOUGHT A HAVELLS ACCL WITH GENERATOR STOP FASCILITY(i.e-
BASICALLY IT IS A AUTO CHANGE OVER SWITCH) FOR MY HONDA EXK
2000S HOME GENERATOR (WHICH START IN PETROL & RUN IN
KEROSENE). ACCL HAS 8 POINT. 2 FOR MAINS(PH & NUE), 2 FOR
LOAD, 2 FOR GEN AND 2 FOR IGNITION POINT(X1 & X2). THE
IGNITION POINT IS SPECIALLY FOR AUTO ENGINE STOP WHEN MAINS
POWER RESTORE. I CONNECT THIS X1 & X2 POINT TO THE
GENERATOR STATER MOTOR & EARTHING POINT. BUT WHEN MAINS
FAILS THE GENERATOR COULD NOT START, BUT WHEN DISCONNECT
THOSE X1 OR X2 POINT, THEN THE GENERATOR START. BUT WHEN
MAINS ON THEN THE GENERATOR SHOULD START, AND WHEN I OFF
THE MAINS THE GENERATOR AUTOMATICALLY STOP.
PLESE HELP ME HOW I STOP THE GENERATOR AUTOMATICALLY WHEN
THE MAINS RESTORE.

Question Posted / shubhabrata roy

2 Answers
11537 Views
Honda, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

I BOUGHT A HAVELLS ACCL WITH GENERATOR STOP FASCILITY(i.e- BASICALLY IT IS A AUTO CHANGE OVER SWIT..

Answer / finas

better you dismantil the accl and connect it directly.

Is This Answer Correct ?

2 Yes

0 No

I BOUGHT A HAVELLS ACCL WITH GENERATOR STOP FASCILITY(i.e- BASICALLY IT IS A AUTO CHANGE OVER SWIT..

Answer / ajaykumar

better you ask the supplier.

Is This Answer Correct ?

1 Yes

0 No

Post New Answer

More Electrical Engineering Interview Questions

Percentage losses in power generation?

0 Answers Nespak, Trimax,

if we put a energy meter in 500 kvar capacitor bank ,then how much units show in energy meter per day.

2 Answers

what is the difference between self excited & seperately excited ?

3 Answers

why we choose 50 or 60 hertz not other value for the power system?

4 Answers

Can you any explain about active,reactive and apparent power in power system with example.

1 Answers

bit confused - am i correct in thinking that to determine line to line voltage in a star config 110v 3 phase 4 wire distribution system i would use a voltmeter? I have a circuit configured as an unbalanced load, consisting of three incandescent lamps (1x40w, 1x60w, 1x100w - all 110v rated)connected in a star configuration to a 110v 3 phase 4 wire distribution system. I want to find out what types of meters i would use to obtain: a) each line to line voltage b) the line to neutral voltage across each load c) current flowing in each line and load d) current flowing in the neutral conductor e) power supplied to the loads im assuming i would be using ammeters in series along each line and voltmeters in parallel across each line to neutral? Also how could i predict these meter readings before taking them and with which formulae? Any help would be greatly appreciated A.

1 Answers

The moisture in air will condense at

0 Answers Caterpillar,

i have 6oo kva dry type transformer and its neutral is not grounded even body of transformer ground i want to know it is safe or not ?

2 Answers

how to prepare the technical test

0 Answers RRB,

What type interview questions ask in Electrical technicians

0 Answers

Dear Mr B C pal...Can you plz. put some light on principle of operation of Z-Ct in conjunction to its use with 1Cx1000Sqmm HT Cables & Directional Ground Fault / Over Voltage Relays...Regd..Parag v K 9899115632

0 Answers

How to calculate earth fault current for 6.6 KV , 50 HZ , 756 Amps , 3000 RPM , 0.8 PF generator

0 Answers

For more Electrical Engineering Interview Questions Click Here