If I have a motor of 1 MW with 6.6 kV, running at 35% load, how can I save ener

Categories >> Engineering >> Electrical Engineering
Suggest New Category

If I have a motor of 1 MW with 6.6 kV, running at 35% load,
how can I save energy without reducing the load?

Question Posted / karteekkarteek001

6 Answers
8781 Views
Reddy Labs, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

If I have a motor of 1 MW with 6.6 kV, running at 35% load, how can I save energy without reducing ..

Answer / k.prakashchandra

power factor correction

Is This Answer Correct ?

2 Yes

0 No

If I have a motor of 1 MW with 6.6 kV, running at 35% load, how can I save energy without reducing ..

Answer / mohammad a.monem salama abu se

BY REDUCING THE FREQUENCY

Is This Answer Correct ?

2 Yes

0 No

If I have a motor of 1 MW with 6.6 kV, running at 35% load, how can I save energy without reducing ..

Answer / k.prakashchandra

You can not lower the load ,capacity, and voltage. To save
energy ,you are left with only reduction of line current to
lessen the I^2R losses.The pf of motor is highest at
full ,or nearly full load.At 35% load ,the pf is less and
hence, the line current is more than required to take the
load (HP)

Is This Answer Correct ?

1 Yes

0 No

If I have a motor of 1 MW with 6.6 kV, running at 35% load, how can I save energy without reducing ..

Answer / maheshbabu calicut

by installing VFD(variable frequency drive)we can vary the speed of induction motors.at 35%load you can run the motor at low speed hence saving power

Is This Answer Correct ?

1 Yes

0 No

If I have a motor of 1 MW with 6.6 kV, running at 35% load, how can I save energy without reducing ..

Answer / k.prakashchandra

Replace the motor with one of lower rating.

Is This Answer Correct ?

1 Yes

1 No

If I have a motor of 1 MW with 6.6 kV, running at 35% load, how can I save energy without reducing ..

Answer / karteek

can you please explain in detail

Is This Answer Correct ?

0 Yes

1 No

Post New Answer

More Electrical Engineering Interview Questions

some basic standard questions on transformer.

0 Answers United Engineering,

what is the formula for transformer oil?

1 Answers

why ac current do not save

3 Answers

why generator one end side star neutral point given? if this point not given what happen?

1 Answers

How convergengr of nr method is not dependent on selection of slack bus and how gauss siedel method depends?

0 Answers

1) What is difference b/w impedence relay and differential relay? 2) what are substations equipments? 3) what is difference b/w circuit breaker and isolator? 4)what are the types of circuit breakers? 5) which medium is mostlty used in circuit breakers and why it is used?

1 Answers NTDC,

can any one suggest paper presentation topies for electrical engg?

0 Answers

How to control the dc motor in ac supply without thyristor circuit?

2 Answers

what is the minimum winding resistance of 30hp compressor, to run or to switch on

0 Answers

how many types of ct retio

3 Answers

at work we have a 3 phase motor but on testing one phase isnt getting a reading. it runs 24 hours a day all week. stops and starts well no noise or heating. the phase isnt down to earth.is it just a bad meter reading or not? phases one and three came up with a resistance reading of 0.4 but phase 2 couldnt get anything shows up as open circuit.

0 Answers iGas,

what is the difference between earthing and grounding of electric circuits

5 Answers HCL, Turbo,

For more Electrical Engineering Interview Questions Click Here