if you are standing on 30th floor & you asked to drink a
water through straw .can you? water is in glass at the
ground floor.
- 5 Answers
- 6246 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / joseph
Not possible.
As, the Maximum suction lift even with mechanical means
(ie. pumps) is only 10 meters (equivalent to atmospheric
pressure) [Since the days of Galileo Galilei it has been an
established fact that a surface pump is incapable
of “lifting” or “pulling” water from a reservoir more than
10 metres down].
In practice, the limitation is more like 6-7 metres. If a
reservoir of water or oil is more than 7 metres deep the
pump must be installed at the bottom of the well.
| Is This Answer Correct ? | 6 Yes | 1 No |
Answer / sneha more
no we can't ?
since there are the chances of siphon.
| Is This Answer Correct ? | 3 Yes | 1 No |
Answer / vinodh kumar j
ya we can if a suction pump is kept in the mouth.
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / noufal cp
i agree to joseph,but consider the situation its just a
glass of water and you dont get 10 meters in the straw,u can
lift right?so we cant say 'no' to the question.what u say?
| Is This Answer Correct ? | 1 Yes | 1 No |
I think we can suck the water. though my ans is does not hav
technical proofs. the only thing u hav to do is u hav to
suck off the air in the straw first in steps. ie. suck some
air in the straw then close it. then take a breath and do
that again until water rises to the top. each time u hav to
keep the other end of the straw closed by ur mouth when
sucking and with ur hand wen u r taking a breath. if u wish
to do this at one go u must first exhale out ur lungs then
suck hard so that iar in the straw goes into ur lungs. what
say.........
| Is This Answer Correct ? | 1 Yes | 3 No |
My rotary kiln die 2mtrs x 36 mtrs long bauxite calcination .PL suggest ld fan cap.and pressure.
WHY DOES LORRY TANKERS DESINGNED TO BE IN SPHERICAL(CURVED,ROUND), WHY DOESNOT IT DESIGNED TO BE AS SQUARE OR REACTANGLE IN SHAPE.
5 Answers APSRTC, Schlumberger,
Define extrued aluminum?
What is pour point?
What is the difference between DIN statndard and DN standard for flanges & what does PN mean in DIN standard.
what the raw mill
Mention stefan boltzman contant.
what happens when the spark are introduced before the piston reaches maximum
What is the difference between Gas Turbine and gas engine in Gas Power plant ?
While selecting a diameter of 1 inch which pipe is better, ERW or Seamless ?? OR Out of ERW and Seamless which one gives good results for an impact force of 2700 N??
What are the procedures of starting of diesel engine?
ET interview on 30TH MAY monday in Rajhans guest house anushaktinagar at 8 AM. contact on amit.kapoor18@gmail.com or 09013016142(msg me if not picked). contact to share & know abt interview
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
