-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
what is advantage of hllow shaft over solid shaft aprt from material saving? does hollow shaft absorb more vibration than solid shaft?
4 227541) what is the seewage discharge per person per day taken for design purpose as per IS codes? 2) how to convert gauge to MM like if we measure 18G as our door frame then how much is it in MM ? 3) how much binding wire is required ti tie 100kg steel ? 4) while making rings in steel reinforcement , whether the corners of rings are deducted to take out cutting length ? 5) how much carbon content should be there in steel used for construction purpose? 6) what are fe415 & fe 500 and which bars are used in general civil works?
1 5786Categories >> Engineering >> Mechanical Engineering Suggest New Category Question Asked @ Answers Views select what is advantage of hllow shaft over solid shaft aprt from material saving? does hollow shaft absorb more vibration than solid shaft? 0 5 wat is the meaning of cop of wet suction and dry suction????? 1 171 What is the difference between an axle and a shaft? reply soon frnds........ 4 260 16 inch = 1 ______________? 2 124 What are the steps taken in troubleshooting of a machine e.g extruder ME 0 26 What is a seal? ME 3 133 what is the mean of b.tech? 3 167 what type of pump 2 63 what is differance between ball screw and lead screw ? Amtek 1 86 What is the units of surface tension and also dimensional formula? RRB 3 218 What is meant by cigarcone? RRB 3 120 I want to know flow rate,max pressure drop,heat load,design pressure,test presurre,temp both inlet and outlet of coldside and hot side of 1,2,3,5,5.5,7.5,10,12,15 tons 0 24 why steam power plant is more popular than gas turbine plant? ME 3 304 what is EEE in thermodynamics????? ME 2 223 what is the practical use of ENTROPY? JSW 4 282
1 3394
give me applications of sequence bridges . (used in 3 phase un balanced systems)
Hi guys! Plz help me to answer the following questions. 1. What are the types of transmission line energy losses? 2. Why are the VLF are used some types of services? 3. What frequencies are used for reliable beyond the horizon terrestrial communication without repeaters? 4. To permit selection of 1 out 16 equi-probable, what is the number of bitis required? 5. What is the most common modulation used for telegraphy? 6. What is the multiplexing is used to increase the capacity of the optic fiber? Thanks
WHERE CAN I GET THE PREVIOUS QUESTION PAPERS OF APGENCO FOR THE THE POST OF Tr.ASSISTANT ENGINEER(CIVIL)
Name one of major transformer company in KSA ?
how ratio is calculated for any grade of concrete. for e.g. sppose M20 requires(x;y:z) quantity of cememt sand and aggregate.
Name the boiler that does not need a steam drum.
A 230V dc shunt wound motor has an armature resistance of 0,15Ω.When operating on no load at 650 rev/min the armature current is 6A . The motor takes a full load current of 85A. Calculate the full load speed if the field flux is (i) maintained constant (ii)reduced by 0,03
What is the Boundary value analysis and Equlance class partition for select * from emp
Why are the coupling capacitors required?
What are the properties of roc for z-transform?
reversing of each word in the string
how to calculate freeboard in under ground water tank and technical details
How to convert GSS duct volume in KG for all guages
What is the range of the stator resistance of 3 phase induction motor?
How do You Maintain a structure after getting cube test of low strength.
