Write an access list line which will deny node 20.0.2.1 to anywhere on your network using DNS via UDP. Don't worry about the other access list lines.
2 CCNA 3586You have OSPF traffic flooding your network via one of your router interfaces. Write the access list line that will deny all ospf traffic. Don't worry about the other lines of the access list.
1 CCNA 3660How to see the running-config & startup-config infor from global configuration mode. As we know, from priviledge mode we cn see it by executing command. i.e. Router#show running-config and Router#show startup-config Now wat is the coommands use in global configuration mode o see those info. Router(Config)# ??????
4 CCNA 6356You want to clear the outputs on your serial interface showing errors on the interface. Which command do you type?
1 CCNA 4026Which command will show you if you have a DTE or DCE cable connected to an interface?
DFSS,
4 CCNA 27501Write out a config to permit only the below MAC address to pass traffic through a port on your switch. mac-address 0005.1b00.5b58
4 CCNA 4279Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..
6 CCNA 7451What is the difference between RIP & RIPng???? Can anyone explain it..!!! Thank u in advance.
1 CCNA 17569What is the meaning of PASSIVE interface in RIP, IGRP, EIGRP & OSPF?? Can any one explain..!!!
6 CCNA 22391What is the difference between OSPF Exteral Type 1 (O E1) & External Type 2 (O E2) routes????
4 CCNA 28814Can anyone explain the Split Horizon rule in RIP & also Split Horizon with Poison reverse. Jitu.... U knw wat i expect.. hehehehehe...
2 CCNA 10722What are the difference between IPv4 & IPv6?? Can anyone explain more details about it..!!
HCL,
9 CCNA 17753
Question { 26777 }
How many access lists are allowed per interface?
A. One per port, per protocol
B. Two per port, per protocol
C. Unlimited
D. Router interface +1 per port.
Answer
Is This Answer Correct ? | 40 Yes | 9 No |
Question { 5614 }
Identify the hardware component that stores the bootstrap
program?
A.) ROM
B.) NVRAM
C.) Booter load
D.) RAM
E.) Flash
Answer
Is This Answer Correct ? | 2 Yes | 0 No |
Question { 8981 }
Of the following switching types, which one has the highest
latency?
A.) Cut-through
B.) None
C.) Store-and-forward
D.) Fragment Free
Answer
Is This Answer Correct ? | 0 Yes | 0 No |
Question { 3905 }
With distance vector routing protocols, it is never useful
to send
the same routing update packet back out the same interface
that it was
learned. This concept is called what?
A.) Holddown timers
B.) Poison Reverse
C.) Count to infinity
D.) Split Horizon
E.) Link State
Answer
Is This Answer Correct ? | 0 Yes | 0 No |
Question { 7037 }
Identify the 2 commands that copies the configuration in
NVRAM to
RAM?
A.) copy backup-config running-config
B.) configure nvram
C.) copy startup-config running-config
D.) configure memory
Answer
Is This Answer Correct ? | 1 Yes | 0 No |
Question { 5470 }
What should be the first command to create an access-list that
prevents all users on subnetwork 10.10.128.0, using subnet mask
255.255.192.0, from being
able to telnet anywhere?
A.) access-list 101 deny tcp 10.10.128.0 0.0.63.255 any eq
telnet
B.) access-list 101 deny tcp 10.10.128.0 255.255.0.0 any eq
telnet
C.) access-list 101 deny tcp 10.10.128.0 255.255.192.0 any
eq telnet
D.) access-list 101 deny tcp 10.10.128.0 0.0.192.255 any eq
telnet
E.) access-list 101 deny tcp 10.10.128.0 0.0.128.255 any eq
telnet
F.) access-list 101 deny tcp 10.10.128.0 0.0.127.255 any eq
telnet
Answer
Is This Answer Correct ? | 1 Yes | 1 No |
Question { 17094 }
Identify the switching method that receives the entire frame
then
dispatches it?
A.) Cut-through
B.) Receive and forward
C.) Store and forward
D.) Fast forward
Answer
Is This Answer Correct ? | 7 Yes | 0 No |
Question { 7306 }
What is the command to start IP RIP version 1 routing on a
Cisco router?
A. show rip
B. enable rip
C. router enable
D. router rip
Answer
Is This Answer Correct ? | 2 Yes | 2 No |
where can we see the OS in the system?
Answer
Is This Answer Correct ? | 21 Yes | 0 No |
What are the advantages and disadvantages of router
Answer
Is This Answer Correct ? | 460 Yes | 75 No |
Question { 8742 }
Can you perform the OSI model seven layer functions in
either two layer or three layer.
Answer
Is This Answer Correct ? | 9 Yes | 0 No |
What is flow and error control?
Answer
Is This Answer Correct ? | 55 Yes | 2 No |
Question { 4328 }
Hi-
Salmaan my name is Shadab Khan and nick Khangkp
ok salmaam plz tell me about of NAT plz
Answer
Is This Answer Correct ? | 1 Yes | 0 No |
consider any webaddress. for example http://www.yahoo.com.
what are the protocols are used and what are the osi layers
are involved in this webaddress?
Answer
Is This Answer Correct ? | 0 Yes | 10 No |
i forget the startup password on Windows XP how to remove?
Answer
Is This Answer Correct ? | 3 Yes | 9 No |