Interested to Buy Any Domain ? << Click Here >> for more details...
HOW TO SELECT DG SETS AND DETAILED INFORMATION OF THE TERMS INVOLVED IN THE BROCHURES OF THE COMPANY?
1758WHAT IS A TR REQUIRED IF AIR FLOW 6500 CMH COIL INLET TEMP 7 - 12 DEGREE C AIR TEMP INLET - 18 DEGREE C & REQUIRED TEMP IS 12 DEGREE C
TATA,
3568one ball fall from a roof & after two hits of to floor it's reach up to half of the roof height. than what is the cofficient of restitution.
BARC,
1 2710The 4/5th part of volume of a piece of wood is swiming as well as sunk in a fluid. if the relative dencity of wood is 0.8 then what will be the dencity of fluid in KG/M3. PLEASE ANSWER WITH SOLUTION.
2 4618HELLO SIR VERY GOOD EVENING SIR,
I'M KALAMANI. I NEED TO PREPARE FOR
UPCOMING "JINDAL STEEL AND POWER LTD" INTERVIEW. I'M
MECHANICAL ENGINEER SIR. SO PLEASE SEND ABOUT JINDAL's
PREVIOUS APTITDE TEST QESTION PAPERS TO MY MAIL ID :
A Wheel accelerates from rest with an acceleration of 6 rad/sec seq. How many revolutions are experienced in 4 sec.? give answer with solution.
4 12384draw neat sketch of pirani gauge with wheatstone bridge circuit to measure output. discuss its construction working princple
Ksb,
3045Post New Mechanical Engineering Questions
What are the properties of fuel oil?
What will you check if one cylinder of your engine is not like the others?
What is wet corrosion and galvanic corrosion?
hai friends please send me the previous question ntpc questions both tecnical and apptitude papers for my mail. and also post me the areas in which u have faced difficulties that might help ful to me. so please send the answer to my question. my mail id is sweety4834u@gmail.com
2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand
What will you do when scavenge fire happened?
What is the material used ball screw rod
Did you have a favorite project that you had to do while in school?
Who all falls under the Perview of Excise Duty, we mean who has to pay the Excise Duty, eg: does all mfrs have to pay ED or who has high turnover they should only pay ED, if yes that what is the Turnover limit?
What is the difference between stalling and surging in rotary compressions ?
what is threaded joints ,where present usage ?
Who built the trans alaska pipelene?
what is the magnetic (electric) center)
What do you understand by critical points in iron, iron-carbide diagram ?
What is the difference between proof resilience and modulus of resilience ?
