Civil Engineering Interview Questions
Questions Answers Views Company eMail

WHAT IS THE MELTING POINT OF STEEL?

Akshaya,

2 4684

WHAT IS THE DIFFERENCE BETWEEN FACTOR OF SAFETY AND PARTIAL SAFETY FACTOR?

1 3530

what do you calaculate PCC/GRADE 10

L&T,

2 6895




what is the standard brick frog size ?

12 28211

WHICH IS BETTER,BURNT BRICKS OR SOLID BLOCK IN CEMENT MORTAR

2 3073

What Should be the CBR Value for Transported (Selected) Soil.whether it can be 5% or not ?

Jindal,

3 2811

how the calculatio is taken for shuttering in staircase.

JMC Projects, Tech Mahindra, TechnoArt,

1 16945

What is the frequency of sampling for the materials of cement,Fine aggregate, Coarse aggregate .and refer which code

IVRCL, Techno Art Constructions,

1047




what is the slump of pile concreting work? give me the value of minimum and maximum value of slump and how give slump in pile?

3 3790

How much quantity of steel will be used for commercial building consists of ground floor shops, first floor shops, second floor will be for offices and third floor will be office/banks. How many tons of steel is required to construct this building.

CRPF,

3 3953

How many Rod required for 58 feet by 24 feet roof slab which is supported by 5 * 3 = 15 Column. Six Stored building Roof Slab = ? Ton 15 Column = ? Ton Slab Beam = ? Ton

883

clear cover for concrete structures as per BS

5 4594

How does a traffic light signal work ?

KCP,

890

IN LOW RISE BUILDING PER SQ FT HOW MANY MATERIAL REQ. SAND &CONCREATE&CEMEBT

ZCL,

1 2819

What is difference between code and standard and specification?

963


Post New Civil Engineering Questions






Un-Answered Questions { Civil Engineering }

What is the standard specification of MOR and Water Absorption of Homogenous Ceramic Floor Tiles?

864


1. For 10sq.m area(47 kg bitumen contain) of 45 mm thick bitumen mix layer..how much bitumen is required for 1600 sq.m and how much aggregate need for that ?? 2. And much tonnage of bitumen mix required for 10 sq.m area of 45 mm thick. Please give answer...

594


Material calculation of cm 1:6 for 1sqm

638


if we know load bearing capacity of the soil and building load falling in each footing, then how to choose the type of foundation??? and if it is shallow foundation then which type of shallow foundation should be choosen i.e either strip or isolated or raft or combined or cantilever footing???????

999


if dia of slab beam bar is38mm what its clear cover any method of provide clear cover

862






How is improve my knowledge in construction industries....

889


Design a cantilever type retaining wall to retain sand for 4m above the ground. The sand fall slopes at the rate of 1 vertical to 2 horizontal. The weight of sand is 18000 N/m3, the angle of repose being 30. The safe bearing capacity of the soil is 200 kn/m2 at 1/25m below the ground level. Use m 15 concrete mix.

1527


i am completed my b.tech EEE in 2009,,,iam trying the job 3+ for AUTO CAD (ELECTRICAL),, what is the market for autocad electrical in hyderabad... how to handle the intervws give some suggestions ?

706


plz.show development and anchorage length in simple diagram.

1261


i want to ecil (Electronics Corporation of India Limited Hyderabad) previous civil engineering question papers immediately please.............

1745


Spider cracks occur in beam bottom due to––

870


a) we have 30nos., 300mm dia, 4m length double under reamed piles.calculate excavation quantity.b) tell concrete qty. also.

9832


while doing the structural works of a simple ground+1 villa, can the columns be continued immediately after neck columns without tie beam, while the tie beam to be done after columns concreting.

353


50 acre of land to be reclaimed for an average height of 2.5 mt. Dredging area is 500mx200m size. what is the dredging depth required to reclaim the area?

225


how to calculate the scour depth

1428