May I have a brief note above the voltage barriers? Whats is the purpose? Please mail me if you've operational details, mail id: email@example.com
where Pirani gauges are uesd in case of pressure measurement?3 5108
What s PDS & PDMS tools ?its role in instrumentation?1 8387
generally for transmitter we are giving supply 24vlts?but we are getting output 4-20ma ? how it is possible? is there any operation inside the tx?pls give complete information?3 4631
units of pressure,flow, level,temperature? principle of pressure gauge? calibration of pressure tx., level tx., temperature tx.flow tx.? description of two wire ,three wire and four wire R.T.D.? WHAT IS INPUT AND OUTPUT OF TX.? WHAT IS INPUT AND OUTPUT OF R.T.D. AND THERMOCOUPLE? WHAT IS HOT LOOP AND COLD LOOP? WHAT IS INPUT AND OUT PUT AND OUTPUT OF D.C.S. AND P.L.C.? PRINCIPLE AND WORKING OF HART? WHAT IS PNP AND NPN PROXY? CALIBRATION OF PRESSURE ,LEVEL ,FLOW SWITCH? DESCRIPTION OF FIELDBUS FOUNDATION? WORKING OF SOV.?2 3686
HI FRIENDS IHAVE QUESTION 1.WHAT IS PARTIALSTROKE TEST?WHY IT IS USED ON ESD ON OFF VALVES?
HI FRIENDS IHAVE QUESTION 1.WHAT IS PARTIALSTROKE TEST?WHY IT IS USED ON ESD ON OFF VALVES?3 5794
Why 4ma - 20ma signal used in instrumentation??5 11783
what is installation and commissioning of (fat & sat) of power plant dcs ? this question keeps in desirable conditions of one company .3932
what is the safety integrity levels (SIL)1 3588
hello sir/madam, I,Subramanian need 5yrs placement papers of officer trainee of Instrumentation technology.pls send to this mail id firstname.lastname@example.org please do the needful. with regards, subramanian.v1258
what is the Difference betwee the Hart and smart series Pressure transmitter1 1979
why the positioner output is 3-15psi5 7843
A flange is used for instrument connection for a system with a design temperature of 316C (600F) and a design pressure of 1000 kPa (145 psi). What is the class rating of the flange to be used for this application? Explain your answer
How many ohms are required for proper earthing?
What is the right procedure for adjusting the gap voltage of bently nevada vibration sensor?
is there any digitel grevity meter availaible in the market by which we can measure specific gravity of a battery?
when the instrument tapping on pipe line is located below and transmitter is located above the tapping point for liquid service transmitter, what should we do, is there any additional drain valve is required??
If a control valve is hunting means means if we are giving 50% to the cv, the cv will open at 51% then slowly slwoly it will reaches 49% , so what to do for solve this problem. The cv is double acting and mounted for anti surge operation, it having 4 nos. volume booster, one sov, one positioner, etc..?
how to check earthing,what is minum ohms for proper earthing
what is difference between fork type and capacitance type level switch. where it is using
In my company plc based winders are operated. one day there was a data transmission failure alarm shown on pc. as per sir instruction we have reset master plc but winders were not triped and alarm gone. so what master plc do?
Explain the mechanism behind the turbine meter.
any questions on motor and energy conversions machines?
In dcs panel we are using diff type of modules ?what is module ? what is the use of modules ?diff type of module?
what are the selections available in configuring a burnout protection of a controller? thanks
Where Can i take a SPI INtools training in Mumbai? In Rolta India Ltd to whom I should approach regarding of SPI INtools Training?
I am having a Phoenix digital to modbus converter. The o/p of the same is connected to flow computer FB407. But the digital signals are updated only after one minute in the flow computer. what may be the cause of delay in communication? Flow computer is having a scanning period of less than 1 sec.