Answer / jitendera kumar sinha

The Network Administrator manually configures the remote
networks.

Identify the command to display all the valid commands at the given mode? A.) Help all B.) Help C.) All commands D.) ?

2 Answers  

---

What is true when creating static route? A.) The mask parameter is optional B.) The administrative distance is required C.) The gateway parameter is required D.) The administrative distance is optional

1 Answers  

---

How does a switch use store and forward? A.) By using a Class I repeater in a collision domain B.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface C.) By using broadcast addresses as source addresses D.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets

1 Answers  

---

Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#

2 Answers  

---

Which is true regarding half duplex Ethernet operation? A.) Half Duplex ethernet technology provides a transmit circuit connection wired directly to the receiver circuit at the other end B.) Half duplex transmission between stations is achieved by using point to multipoint Ethernet and Fast Ethernet C.) With Half Duplex transmission logically circuits feed into a single cable creating a situation similar to a one way bridge D.) Half Duplex transmission between stations is achieved using Point to Point Ethernet & Fast Ethernet

1 Answers  

---

friends i have 3ree prob which is asked in ibm india in technical round 1 what is ftp(this was easy i had answered) 2 why we use ftp(i think it is a tough one) 3 how can we enable ftp in the widows xp. friend i need these question answer as soon as possible if it is possible to reply within the eveing then i always obeyliged to you i am espacily looking towards the jitendera sinha who make most of the valuable answer loking toward you nidhi mall

3 Answers   IBM,

---

Which command will give the following output: Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int * 0 CTY - - - - - 0 0 0/0 - 1 AUX 9600/9600 - - - - - 0 0 0/0 - * 2 VTY - - - - - 2 0 0/0 - 3 VTY - - - - - 0 0 0/0 - 4 VTY - - - - - 0 0 0/0 - 5 VTY - - - - - 0 0 0/0 - 6 VTY - - - - - 0 0 0/0 -

1 Answers  

---

here is your question sahin Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP. I knew about it from ICND 2 cisco press book. Three more questions - a) If we change the K value (I mean metric weight)on a router what will happen??? b) When redistribution is necessary in EIGRP. Is there any condition for that??? c) What is reference bandwidth for metric calculation in EIGRP. As we know, in OSPF, on a CISCO router reference bandwidth is 10Mbps.

3 Answers  

---

Urgent reply plz donot have time to serch on google plz reply the questions is how to remove newfolder.exe virus from my windows 2003 server i have all ready tried quick heal.spy hunter mcafee server . plz reply

4 Answers  

---

Identify the command that displays the SAP table? A.) show ipx servers B.) display SAP table C.) display SAP's D.) show sap table

1 Answers  

---

Which three statements about common elements of the TCP/IP protocol stack are true? (Choose three) A. IP provides connectionless service and routing capabilities B. APP enables devices to locate the IP address of local devices C. UDP provides simple connectionless service without windowing or acknowledgments D. ICMP provides connection oriented management data to routers and Layer 3 switches E. TCP enables devices to send large quantities of data using windowing in a connection oriented manner

2 Answers  

---

Identify the command to determine if an IP access-list is grouped on interface e0? A.) Router(config)# show ip interface e0 B.) Router> show ip interface e0 C.) Router# show interface e0 D.) Router# show ip interface e0

1 Answers  

---