If you have configured IPX on a Serial interface, which command would display the IPX network and node address on the Serial 1 interface? A.) show interface B.) show ipx s1 C.) show interface s1 D.) show ipx int serial 1 E.) show ipx int brief

1 Answers  

---

What is the default bandwidth of a serial connection? A.) 1200 baud B.) 1.544 Mbps (T1) C.) 10 Mbps D.) 96Kpbs

4 Answers  

---

In which ios version 182 people can access router through telenet?

0 Answers  

---

My ccna certification is allready expried but I could not apper the ccnp exam due to some personal problem. Currently i am working as network administrator .Can it create any problem for my next job . and how can i apper he ccnp exam. Please help me and give me what is the solution.

1 Answers   PCS,

---

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 Answers  

---

How can an Ethernet switch improve network performance? Choose three

2 Answers  

---

Identify the hardware component that stores the bootstrap program? A.) ROM B.) NVRAM C.) Booter load D.) RAM E.) Flash

2 Answers  

---

Which command will display the IPX routing table? A.) show routes B.) show routes ipx C.) show routes protocol=ipx D.) show ipx E.) show ipx route

1 Answers  

---

Which layer is responsible for providing mechanisms for multiplexing upper-layer application, session establishment, and tear down of virtual circuits? A.) Session B.) Network C.) Physical D.) Transport E.) Application F.) Presentation

2 Answers  

---

HI friends mine one of the friends have ask a good question i also donot know the answer so i am putting here Please poet the answer no matter it is wright or wrong put yours view here The question is like that when we are going to configure ospf then there are three way 1st way router ospf 10 netwrok 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 the 2nd way is like that router ospf 10 netwrok 192.168.0.0 0.0.255.255 area 0 but he inrodused the thrird way like router ospf 10 netwrok 192.168.00000001.0 < ?.?.?.?>area 0 router ospf 10 netwrok 192.168.00000010 <?.?.?.?>area 0 now problem is that what should i put the mask in this way so i puted ? sign Please solve this problem i think this is good one plz donot see for answer please contribute any thing i am reqesting Than you Jitendera kuamr sinha

5 Answers  

---

which is following route will be used to froword data in a situation where a routing table tables contains static ,RIP,IGRP routes destined to the same network with each set to its default administrative distance

9 Answers   HCL,

---

What does the IPX maximum-path command do? A.) Allows you to disable the TTL on an IPX packet B.) This parameter is only used in NLSP routing C.) Sets the maximum metric that can appear in the routing table D.) Configures round robin load sharing over multiple equal metric paths (parallel paths)

1 Answers  

---